Regency Fireplace Products Horizon HZ40E-LP10 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 64

background image

Regency Horizon™ HZ40E-10 Gas Fireplace

|

43

|

43

installation

919-405

05/20/14

To Wire Fan Motor

10. Connect one of the black wires from the power cord to the black wire

included with the fan (light blue connector). Connect the other end to

one spade on the thermodisc

11. Connect the red wire to the other open spade on the thermodisc. Connect

the other end to the black wire from the fan motor.

12. Connect the white wire from the fan motor to the black wire on the power

cord (dark blue connector).

13. Slide the thermodisc on to the bracket clip on the bottom of the unit.

Ensure no wires will touch the hot surfaces.

9.

Secure the fan to the base with 2 screws. Note the right access panel

was removed to allow easier access to the right side screw.

14.. Secure the ground wire from the fan assembly and the power cord to

the ground lug located on the back left near the fan.

15. The fan control module (supplied with the fan kit) secures to the side

access panel. Remove 2 top screws and loosen 2 bottom screws to

remove the side access pane

17. Plug in the fan power cord to the Fan Control Module into the outlet

marked “Fan”. Plug the FCM-COM wire from the remote control wiring

harness into the location on the Fan Control Module marked “COM”.

Turn the switch on the Fan Control Module to the ON position. ON is to

the left. The “O” is the off position

16. Install the fan control module (FCM) into the bracket on the side access

panel. Plug in the power cord to the outlet in the unit.

4

HZ40E

«
...
41
42
43
44
45
...
»

Содержание Horizon HZ40E-LP10

































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ40E-LP10

Бренд: baltur Страницы: 92

Бренд: Empire Comfort Systems Страницы: 4

Бренд: Napoleon Страницы: 14

Бренд: Continental Fireplaces Страницы: 48

luna diamond 550 v

Бренд: M Design Страницы: 27

Бренд: Sherwood Страницы: 8

E-SLIM LINEAR 1200/450 I

Бренд: Faber Страницы: 31

Бренд: Dimplex Страницы: 2

Бренд: HAMPTON BAY Страницы: 7

Бренд: Valor Страницы: 80

Бренд: Valor Страницы: 42

Garden Lights 26380

Бренд: Landmann Страницы: 4

Бренд: Pur Line Страницы: 52

Бренд: Style selections Страницы: 33

Бренд: Country Hearth Страницы: 20

Бренд: Royal Страницы: 56

Бренд: IHP Страницы: 4

Бренд: IHP Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды