Regency Fireplace Products Greenfire GFi350L Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 48

background image

Models: GFi350LNG-R

GFi350LLP-R

GFi350LULPG-R

Owners &

Installation

Man

ual

October 11, 2017

LISTINGS AND CODE APPROVALS

These  gas  appliances  have  been  tested
in  accordance  with  AS  5263.0,  AS/NZS
5263.1.3  and  have  been  certified  by  the
Australian Gas Association for installation
and operation as described in these Instal-
lation and Operating Instructions.

Your unit should be serviced annually by
an authorised service person.

919-769a

Greenfire

®

GFi350L Gas Inbuilt

FOR YOUR SAFETY
What to do if you smell gas:

Do not try to light any appli-
ance

Do not touch any electrical

switch: do not use any phone
in your building.

Immediately call your gas

supplier from a neighbour's
phone. Follow the gas sup-
plier's instructions.

If you cannot reach your gas

supplier, call the fire depart-
ment.

WARNING:
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Refer to this manual. For
assistance or additional information consult
an authorised installer, service agency or
the gas supplier.

FOR YOUR SAFETY
Do not store or use gasoline or other flam-
mable vapours and liquids in the vicinity of
this or any other appliance.
Installation and service must be performed
by an authorised installer, service agency or
the gas supplier.

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

1
2
3
...
»

Содержание Greenfire GFi350L

















































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GFi350L

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 84

Бренд: Napoleon Страницы: 16

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 56

Бренд: Napoleon Страницы: 36

Бренд: Napoleon Страницы: 24

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 52

Бренд: Napoleon Страницы: 40

PATIOFLAME GPFN

Бренд: Napoleon Страницы: 32

Бренд: Napoleon Страницы: 36

Бренд: Waterford Страницы: 24

Бренд: Rinnai Страницы: 21

Бренд: Enviro Страницы: 4

Бренд: Empire Страницы: 44

Бренд: Ravelli Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды