manualshive.com logo in svg

Regency Fireplace Products Greenfire GF900C-LP2, Инструкция для владельца и по установке

Поделиться
Скачать
Regency Fireplace Products Greenfire GF900C-LP2 Скачать руководство пользователя страница 30

30

Regency GF900C-2 Gas Fireplace

installation

FLUEING ARRANGEMENT FOR VERTICAL TERMINATIONS
Vertical Flueing with One(1) 90

o

 Elbows (1 - 90

o  =  

2 - 45

o

)

The shaded area in the diagram shows all allowable combinations 
of straight vertical and offset to vertical terminations, using two 
45

o

 elbow, with Rigid Pipe Flueing Systems.

•   Flue must be supported at offsets.

•   Maintain  clearances  to  combustibles  as  listed  in  the 

"Clearances" section.

•   Horizontal flue must be supported every 3 feet.

•   Firestops are required at each floor level and whenever 

passing through a wall.

•   Must use optional rigid pipe adaptor (Part# 510-994) when 

using rigid pipe flue systems.

•  Refer to the "Flue Restrictor Position" section for details on 

how to change the flue restrictor from the factory setting of 
Set 0 to Set 1 or Set 2 if required.

6.7m

4m

Restrictor Set #3

15mm open

"THIS UNIT MUST ALWAYS 
TERMINATE / FLUE 
DIRECTLY TO THE OUTDOORS."

N

OTE

: Restrictor settings

Propane: Set #2 - 18mm
ULPG: Set#1 - 26mm

Содержание Greenfire GF900C-LP2





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды