Regency Fireplace Products E18E-LP11 Скачать руководство пользователя страница 24

Страница: 24 / 104

24 |

Regency

E18E-11 Gas Fireplace Insert

installation

E18E

SEPARATING THE OUTER FIREBOX SHELL FROM INNER FIREBOX

1. Lay fireplace insert on flat surface (use a drop sheet to protect surface).

2. Remove Glass Door by removing 2 x Phillips screws at the bottom of Glass Door Frame.

3. Remove burner by removing 2 x Phillips screws, take note of how aeration adjustment rod is routed.

4. Remove 2 Phillips screws from top left and right side (Thermodisc bracket).
Remove 2 x 1/4" Hex head screws from top left side and right side of inner firebox.

5. Remove 4 Phillips screws - 2 per side, located on the bottom base of the firebox. Place

screws and panel brackets aside for reinstallation.

6. Carefully lift out the inner firebox and set aside until required. Use caution with sleeved

wires on the left side, place inner firebox aside.

7. Outer firebox shell is ready for installation.

Refer to particular approved appliance in which the E18E is being installed into for the
following:

    Existing unit modifications
    Adaptor setting
    Required flex length
    Leg setting / outer shell position both need to be

exact as measurements indicated.

Outer shell

Before separating Outer Shell and

Unit—Clear wire harness

Aeration adjustment Rod

Burner

Remove screws from these locations

Hex Head

Screws

Phillips

Screws

f i r e - p a r t s . c o m

Содержание E18E-LP11









































































































Результаты поиска

Содержание E18E-LP11

Отзывы:

Похожие инструкции для E18E-LP11

Бренды по названию

Популярные бренды

Regency Fireplace Products E18E-LP11, Инструкция для владельца и по установке

Результаты поиска

Содержание E18E-LP11

Отзывы:

Похожие инструкции для E18E-LP11

Бренды по названию

Популярные бренды