Regency Fireplace Products E18E-LP11 Скачать руководство пользователя страница 66

Страница: 66 / 104

66 |

Regency

E18E-11 Gas Fireplace Insert

installation

CONVERSION KIT 617-977 - NATURAL GAS TO PROPANE USING SIT 886 GAS VALVE

Each Kit contains one LPG
Conversion Kit
LPG Conversion Kit Contains:

Qty. Part #

Description

904-977

Burner Orifice #55

918-590

Decal "Converted to

LPG"

908-528

Red "LPG" label

904-529

5/32" Allen Key

1 911-009

Hi/Lo regulator

1 910-037

LPG Injector (Pilot Orifice)

920-028

Instruction Sheet

Conversion from NG to LPG

for E18E using SIT 886 NOVA Gas Valve

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

10. Reinstall new burner orifice LPG stamped

#55 and tighten

11. Remove Hi/Lo pressure regulator by

removing 2 screws as shown below.

Reverse steps to install LP pressure

regulator.

Pull off the pilot cap to expose the pilot
orifice.

Unscrew the pilot orifice with the allen key;
then replace with the LPG pilot orifice and
the pilot cap, provided in the kit.

Remove burner orifice with a 1/2" wrench.
Use another wrench to hold on to the elbow
behind the orifice. Discard orifice.

Burner Orifice

Installer Notice:

These instructions must be left with the

appliance.

12. Attach the label “This unit has been

converted to LPG” near or on top of the
serial # decal.

13. Replace yellow “NG” label with red “LPG”

label.

14. Reverse steps 3 - 1.

15. Check for gas leaks.

16. Check inlet and outlet pressures.

17. Check operation of flame control.

18. Adjust the burner aeration setting to Fully

Open and adjust as required for the best
flame picture.

19. See manual for Gas Pressure Testing

instructions

1. Turn the unit off and allow it to cool to

room temperature.

2. Unplug or disconnect power source to

stove.

3. Remove glass front (see manual).

4. Remove Log or Glass Burner (see

manual).

5. Unscrew NG burner orifice and replace

with LP orifice.

Burner Orifice

Remove pilot retainer clip with pliers and
pull off the pilot cap to expose the pilot
orifice.

Pilot retainer clip

920-028

01.14.19

E18E

f i r e - p a r t s . c o m

Содержание E18E-LP11









































































































Результаты поиска

Содержание E18E-LP11

Отзывы:

Похожие инструкции для E18E-LP11

Бренды по названию

Популярные бренды

Regency Fireplace Products E18E-LP11, Инструкция для владельца и по установке

Результаты поиска

Содержание E18E-LP11

Отзывы:

Похожие инструкции для E18E-LP11

Бренды по названию

Популярные бренды