REGATRON TC.ACS Скачать руководство пользователя

Страница: 49 / 66

Option: Analog I/O Adaptor (TC.ACS X609 Adapter)

Application

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

49 / 66

10 Option: Analog I/O Adaptor (TC.ACS X609 Adapter)

10.1 Application

The analog I/O adaptor is designed to offer an easier access to the interface X609 on the rear side of the TC.ACS

device (see

3.2

) than the original M12 flush-type connector. It can be connected to the interface X609 via its

interface X630 and it also offers the interface X609 itself. In addition, it provides BNC connectors as well as a

multiple connector that individually represent the pins of interface X609 (see

3.2.3

10.2 Interfaces on the Front

Tab. 6:

Interfaces of the analog I/O adaptor (front, from right to left), bold letters indicate the status of delivery

The input and output of the TC.ACS X609 adaptor can be filtered by a low pass filter, if

necessary (see

10.4

Interfaces on the front of the analog I/O adaptor

Interface

Type

Pins of X609 of TC.ACS

Signal

Description

X631

8-pin multipole

connector

Pins 1 - 8

AIN1

Analog input 1 (filtered or

unfiltered

)

AIN2

Analog input 2 (filtered or

unfiltered

)

AIN3

Analog input 3 (filtered or

unfiltered

)

AIN4

Analog input 4 (filtered or

unfiltered

)

GNDA_ISO

Analog ground

+10V_ISO

+10V reference voltage

-10V_ISO

-10V reference voltage

GNDA_ISO

Analog ground

X632

BNC female

Pin 9

AOUT1

Analog output 1 (

filtered

or unfiltered)

X633

BNC female

Pin 10

AOUT2

Analog output 2 (

filtered

or unfiltered)

X634

BNC female

Pin 11

AOUT3

Analog output 3 (

filtered

or unfiltered)

X635

BNC female

Pin 12

AOUT4

Analog output 4 (

filtered

or unfiltered)

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды