REFUSOL 40K Скачать руководство пользователя страница 49

Страница: 49 / 65

REFU Elektronik GmbH

REFUsol 40K / 46K-MV

Error
Code

Text

Description

Action

consider the line voltages to be in
order, contact the Service.

9001B

RCD fault

The AFI-Board unit has detected a
residual current.
Leads to an immediately shutdown

Check system isolation. As long as
you consider the isolation
impedance to be in order, contact
Service.

9001D

RCD warning

90020

Initialisation C1

Initialisation has failed.

Restart inverter. If this does not
rectify the error, contact Service.

90021

Initialisation C0

90024

SR parameter
error

Error in parameter initialisation. The
device has been permanently shut
down.

Please contact Service.

90029

Update fault

Update failed

The update has failed. Contact
Service.

9002A

Keep Alive

Internal communication monitoring
has determined a fault.

Please contact Service.

9002B

Update End

Update successful notification.

An update was successfully
completed. The device will resume
normal operation.

9002C

AntiIslandPhase
Shift

Islanding of the connected grid
section has been detected

Wait for the grid to become stable
again

9002D

AntiIslandRocof

9002F

FFS is read-only Internal data can't be written

anymore.

Please contact Service.

90030

DC share too
high

The measured DC-Part in AC current
exceed the defined limit.

90031

ETH link lost

The Ethernet cable has been
removed

Check the Ethernet cable on the
device and the receiver (router,
switch) for a correct fit. If the
cables are correctly connected and
should the notification still be
there, please contact Service.

90032

Restart

The system has been rebooted.

Should these notifications occur
repeatedly during daily operation,
please contact Service.

90050

AC condition

AC switch on condition not fulfilled

Wait until the network is stable

Содержание 40K


































































Результаты поиска

Содержание 40K

Отзывы:

Похожие инструкции для 40K

Бренды по названию

Популярные бренды

REFUSOL 40K, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 40K

Отзывы:

Похожие инструкции для 40K

Бренды по названию

Популярные бренды