background image

 
 

11 

Here is a checklist that should be followed for any CT program (courtesy of Monsanto 
NZ Ltd): 

1.

 

Check that the soil pH is around 6.0. 

2.

 

Check soil fertility levels for fertiliser requirement. 

3.

 

Ensure your spray boom has a marking system and is fully operational. 

4.

 

Establish optimum time for planting. 

5.

 

Check and control weeds present, before and during crop establishment. 

6.

 

Check and control insect and slug infestation before and during plant 
establishment. 

7.

 

Ensure soil conditions are suitable for drilling. 

8.

 

Inspect the crop regularly after planting. 

 
Experience has shown that farmers new to CT often have crop failures on the first 
occasion, but as their skills and understanding of the technique improve, so do their 
crop results.  

 

 

TECHNIQUES AND TIMING FOR PASTURE RENOVATION 

There are two basic techniques for pasture renovation, i.e. rejuvenation and renewal.  
Rejuvenation is the most efficient technique and involves sowing the seeds of new 
and virile pasture grasses and legumes direct into existing pasture and have them 
gradually take over the old strain, without causing loss of production due to 
cultivation.  This technique is known as ‘stitching in’.  Renewal involves a total 
herbage control system, i.e. spray off old pasture with a wide spectrum herbicide 
before drilling. 
 
Local knowledge is invaluable when determining which techniques to use and when 
to use them.  The best time for pasture renovation will vary by region, and is largely 
governed by the temperature and weather that follow.  In temperate climates with 
mild winters the autumn is best and tropical climates the spring is the best time when 
the tropical grasses have not recovered from their winter dormancy.  In arid climates 
the time is directly before or after summer rains. 
 
The basic requirement for seed germination is a warm moist seed bed.  The aim 
should be to sow the seed at a time when there is sufficient moisture for quick 
germination, and little likelihood for later drought.  The Aitchison opener/coulter 
however will promote germination in much drier soils than any other known coulter 
when used correctly.

   

Содержание Aitchison Seedmatic 40 D Series

































































Отзывы: