Functional possibilities:
Pairing
1.
Press and hold the Volume Down button (2) of the deactivated parent unit.
2.
Switch on the parent unit by pressing and holding the On/Off button (1). The power indicator (3) starts flashing green. Release both buttons.
3.
Press and hold the Decrease Microphone Sensitivity button (11) of the switched-off baby unit.
4.
Switch on the baby unit by pressing and holding the On/Off button (10). The power indicator (12) starts flashing green. Release both buttons.
5.
Now press the Decrease Microphone Sensitivity button (11) of the baby unit once again. If the pairing process is successful, you will hear two beeps from the
parent unit. The power indicators of the parent unit (3) and baby unit (12) should now light up permanently green.
6.
The baby monitor is now ready for use.
7.
Repeat the pairing process if the parent unit and baby unit do not communicate with each other.
Baby unit / Transmitter
1.
During normal operation, the baby unit transmits in VOX mode. It only transmits the signal when the microphone of the baby unit detects any sounds. You can
use the buttons (11) on the baby unit to increase or decrease microphone sensitivity. The brightness of the night light shows you the level of sensitivity when
you set it. When set to the highest sensitivity level, the baby unit transmits continuously.
2.
The transmission indicator (15) lights up yellow when the baby unit is transmitting sounds.
3.
You can switch the night light on and off with the night light switch (14). When the unit is switched on, you can choose from 3 brightness levels by pressing
the night light switch again. You can also switch the night light to VOX mode, which is indicated by a lit night light VOX display (13). In this mode, the night
light turns on for a few seconds whenever the microphone detects a sound.
4.
Your child can hear your voice through the loudspeaker (19) on the back of the baby unit when you talk to it using the intercom function on the parent unit.
You can increase or decrease the volume of the loudspeaker with the buttons (11) while holding down the Talk button (8) on the parent unit. You can adjust
the sensitivity of the microphone of the baby unit with the buttons (11) without holding down the Talk button.
5.
To switch on the low-radiation ECO mode, press the On/Off button (10) three times in quick succession. ECO mode can be identified by the blue power indica-
tor (12). To return to normal mode, press the On/Off button again three times in quick succession.
! CAUTION: The out-of-range alarm is not active in ECO mode. You will therefore not receive a message on the parent unit if you are no longer within
range of the baby unit or if it is switched off.
Parent unit / Receiver
1.
If the parent unit receives a signal, the LEDs of the noise level indicator (5) light up in relation to the volume of the signal.
2.
You can increase or decrease the volume of the loudspeaker with the buttons (2). The set volume is indicated by the LEDs of the noise level display (5).
3.
If you mute the volume entirely, the parent unit automatically reverts to vibration mode. In this mode, the parent unit vibrates automatically as soon as it receives a signal.
Increase the volume again to switch off vibration mode. Please note that if vibration mode is switched on, battery life will be reduced.
4.
You can use the intercom function to communicate with your baby. To do this, press and hold the Talk button (8) on the top of the parent unit. Please be aware
that you cannot hear your baby while you are pressing and holding the Talk button.
5.
If the parent unit is out of range of the baby unit for a period of more than 30 seconds, you will receive a visual and audible out-of-range alarm on the parent
unit. The alarm will only cease when you are back within range of the baby unit.
6.
Briefly pressing the On/Off button shows you the sound level display (5) of the activated parent unit and the battery status. If the battery level of the parent unit
becomes low, you will receive an optical and acoustic alarm. You can then recharge it using the included mains adapter.
Cleaning and maintenance
Always disconnect the mains adapters from the wall power socket before cleaning the unit. Only use a slightly dampened cloth. Do not submerge the unit in water.
Do not use chemical detergents.
This product does not require any special maintenance. Repairs to the unit must be carried out by skilled personnel only.
4
