5)
Turn the “SYSTEM ON/OFF” switch to the “ON” position, the “SYSTEM” indicator shows GREEN and the system
is activated.
The “SYSTEM” indicator may show RED and all outputs are disabled when the battery operates
for the first time, since the battery may lose its energy in the stock. It just needs to be charged for no more
than one day in bright sunshine, then it shows GREEN and all the output ports are ready to output.
6)
Put on the switches of the outputs that are in use, the indicators will lighten GREEN, and meanwhile, the
corresponding appliances will start to operate. To stop operation, just shut off the associated output switches.
If the appliance with diplex switches such as photosensitive garden lights, it may not work immediately while
the switch is put on. Please refer to related manuals.
7)
All power outputs
except output 1 (6V)
will automatically stop running while the battery is discharged to its low
voltage
limit A
, and the SYSTEM indicator shows ORANGE in the meantime. The
OUTPUT 1 (6V)
will continue to
work and be cut off until the battery station is discharged to its low voltage
limit B
, and the SYSTEM indicator
shows RED. Then ALL output ports stop outputting before the SYSTEM indicator changes to GREEN.
8)
The SYSTEM indicator stays in RED before the battery is recharged to its normal voltage. While it rises to the
normal voltage, the SYSTEM indicator will change to flashing RED-GREEN twice every 10 seconds. It will take
another 2 hours before it changes to GREEN and all output ports start to output at the same time.
9)
The
“Timer On/Off”
ONLY
regulates the running mode of
OUTPUT 3 (18V)
pump between "intermittent mode"
and "continuous mode". In the “intermittent mode” (i.e., “Timer On”), a build-in timer is enabled to run the
pump 10 minutes per hour periodically
to save the energy, and it is especially useful in winter or on cloudy days.
In the "continuous mode", the build-in timer is disabled and the pump shall run continuously.
This function is
available only when the SYSTEM indicator shows GREEN.
10)
While the Timer function is activated, and the TIMER indicator shows GREEN, the pump works, if the indicator
flashes
(once per second)
in GREEN, the pump rests.
11)
Turn the system switch to “Off” position, ALL output ports will be disabled, the battery will still be charged in
the daylight, and then the appliances will have longer operating time when put it to work in the evenings or
special festive occasion.
The battery will always be charged in the sunlight no matter whether the system
switch has been put to “On” or “Off”! And the system will automatically cut off the charging current while
the battery is fully charged.
4.
CAUTION
1)
Any altering of the product itself or changing of components with non-genuine parts voids warranty.
2)
Operate the pump in water only (never above 40°C), especially keep it away
from flammable liquids, and do not use in hazardous areas.
3)
All the connections are protected against reverse polarity as shown in Figure 6.
Don’t insert the plug with reverse polarity by using force.
4)
The pump is dry run protected. The pump will automatically stop when there is
insufficient water.
5)
Do not charge the solar battery back-up by any AC power supply directly; it is
designed ONLY for DC power.
6)
Never connect any appliances whose rated power is larger than the maximum power listed in the below
technical data list. Otherwise it will be automatically cut off.
7)
Do not leave this battery back-up in bad ambient environment.
8)
Do not leave the battery back-up in direct blazing sunlight or expose it to extremes of heat or cold, which can
affect its service life. If possible place the battery in the shadow of the solar panel or your house or even a tree
etc.
9)
Do not dip this battery back-up into water,
its IP grade is 44.
5.
CLEANING AND MAINTENANCE
If the pump starts losing power or stops working after operating for a certain time, please clean the inside of the
pump and any debris on the outer filter cage.
The pump can be opened by unscrewing the four screws on the bottom of the filter housing.
To clean the pump, disassemble the pump according to Figure 7 and then clean all parts with water.
Figure 6
Figure 7