background image

(1) Read owner's manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Handling this machine improperly could result in accidents causing serious injury or

death. Read this manual carefully and practice using the trimmer until you are fully
acquainted with all operations and have learned to use it correctly.

(4) Keep all children, bystanders and helpers 15 meters away from the brushcutter
(5) Keep hands away from cutting blades

If warning label peel off or become soiled and impossible to read, you should contact the dealer
from which you purchased the product to order new labels and affix them in the required
location(s).

Never modify your trimmer.
We won't warrant the machine, if you use the remodeled trimmer or you don't observe the
proper usage written in the manual.

WARNING

IMPORTANT

For safe operation and maintenance, symbols are
carved in relief on the machine. According to these
indications, please be careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE" 
Position: FUEL TANK CAP

(b) The direction to close the choke
Position: AIR CLEANER COVER

(c) The direction to open the choke
Position: AIR CLEANER COVER

3. Warning labels on the machine

4. Symbols on the machine

5

Содержание LRTZ2500

































Отзывы: