background image

16

• Gasoline is very flammable. Avoid smoking

or bringing any flame or sparks near fuel.
Make sure to stop the engine and allow it
cool before  refueling the unit. Select outdoor
bare ground for fueling and move at least
3m(10ft) away from the fueling point before
starting the engine. 

• The RedMax engines are lubricated by oil

specially formulated for air-cooled 2-cycle
gasoline engine use. If RedMax oil is not
available, use an anti-oxidant added quality oil
expressly labeled for air-cooled 2-cycle engine
use. (JASO FC GRADE OIL or ISO EGC
GRADE)

RECOMMENDED MIXING RATIO

GASOLINE 50:OIL 1

• Exhaust emission are controlled by the

fundamental engine parameters and
components(eq., carburation, ignition timing
and port timing) without addition of any
major hardware or the introduction of an
inert material during combustion.

• These engines are certified to operate on

unleaded gasoline.

• Make sure to use gasoline with a minimum

octane number of 90 ROZ(USA/Canada : pump
octane min.87)

• Unleaded gasoline is recommended to reduce

the contamination of the air for the sake of your
health and the environment.

• Poor quality gasolines or oils may damage

sealing rings, fuel lines or fuel tank of the
engine.

HOW TO MIX FUEL

1. Measure out the quantities of gasoline and oil to

be mixed.

2. Put some of the gasoline into a clean, approved

fuel container.

3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for

at least one minute.

5. Put a clear indication on the outside of the

WARNING

50:1 MIXING CHART

GASOLINE     gal.

1

2

3

4

5

2-CYCLE OIL fl.oz 2.6

5.2

7.8 10.4

13

GASOLINE     liter

1

2

3

4

5

2-CYCLE OIL   ml

20

40

60

80

100

7. Fuel

Содержание HEZ2500S





































Отзывы: