RedMax EXTREME EXZ2460S-PH Скачать руководство пользователя страница 22

US-22

EXZ2460S-PH

8. Operation

OPERATING TECHNIQUES
(OP2)(OP3)(OP4)

Operate the RedMax Sweeper at or near
full throttle with its sweeper fins resting on
the work surface. 

• It is both tiring and unnecessary to lift

or hold the fins from the work surface
during sweeping. 

• When sweeping narrow areas such as

sidewalks, the RedMax Sweeper can
be used to throw material directly
ahead of the operator. Clearing wider
areas may require sweeping at an
angle to create windrows to one side of
the path being cleared. 

• Windrows of lighter materials often can

be combined into one main row or pile
for eventual pickup, while heavy or
bulky material may need to be collected
row-by-row. 

• To pull debris from corners, reverse

sweeper drum rotation by turning the
powerhead over (throttle facing "up") . 

• Sweeping corners with the RedMax

Sweeper upside down. (OP3)

(1) Direction of rotation

• For long-term inverted operation,

loosen the adjustment knob to reverse
the handle. (OP4)

(1) Adjustment Knob

Reversing the RedMax Sweeper will
cause debris to be thrown back toward
the operator. When reversing the
RedMax Sweeper, use lower throttle
settings and beware that thrown debris
may also affect your footing! 

OPERATING AND SAFETY TIPS
(OP5)

Maintain a shallow angle to the work

surface! 

• A high angle of operation tends to

propel the broom toward you, risking

WARNING

WARNING

NOTE

loss of control of the machine. 

(1) Maintain a shallow working angle. 
(2) A steep working angle risks loss of

control!

The sweeper belts may rotate when the
RedMax Sweeper is started! 

• Always maintain a firm grip when

starting the RedMax Sweeper. Beware
of objects that could become entangled
in or be thrown by the rotating sweeper
belts. 

YOU MUST ALWAYS GUARD AGAINST
THROWN DEBRIS! 

• Although the RedMax Sweeper’s

sweeper belts are less forceful than a
lawnmower blade, you must avoid any
operation where thrown objects could
pose a threat to persons or property! 

Never operate the RedMax Sweeper if
any protective devices (engine covers,
stop switch, etc.) are missing or
damaged! 

Never operate the engine at high rpms
without a load! 

• Doing so could damage the engine. 

Avoid low rpm operation 

• Continuous low-rpm operation can lead

to premature clutch failure. 

GENERAL SAFETY INSTRUCTIONS

Work Safely 

The operator or bystanders can be injured
if the RedMax Sweeper is misused or
abused. Never allow a person without
training or instruction to operate your
machine. 

Never make unauthorized attachment
installations. 

Stay Alert 

You must be physically and mentally fit to
operate this machine safely. 

WARNING

RMS-EX  OP2

RMS-EX  OP3

RMS-EX  OP4

RMS-EX  OP5

Содержание EXTREME EXZ2460S-PH
































Отзывы: