RedMax BCZ2600S Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 44

RedMax BCZ2600S Скачать руководство пользователя страница 6



6



For safe operation and maintenance,
symbols are carved in relief on the machine.
According to these indications, please be
careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position:

FUEL TANK CAP

(b) The direction to close the choke

Position:

AIR CLEANER COVER

(c) The direction to open the choke

Position:

AIR CLEANER COVER

4. Symbols on the machine

IMPORTANT

ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2

AND 2001 CALIFORNIA EMISSION

REGULATIONS FOR SI SORE’s

COMPLIANCE PERIOD : CATEGORYA:

ENGINE FAMILY : 1KZXS.0254QR ; EM
ENGINE DISPLACEMENT : 25.4cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

Ce moteur est conformc aux normcs U.S.

EPA PH2 et 2001 ainsi qu’aux autres dispositions
ultérieures de la réglementation concernant la pollution
de l’air pour les petits moteurs tout-terrain avec une
période de accordable : CATEGORYA.

Type de moteur : 1KZXS.0254QR :EM
Cylindrée du moteur : 25,4cc

Se référer au Manuel de l’utilisateur pour les
spécifications d’entretien et les réglages.

INFORMATION IMPORTANTE
CONCERNANT LE MOTEUR

«
...
4
5
6
7
8
...
»

Содержание BCZ2600S













































Отзывы:

Нет отзывов