background image

Winter Storage

The machine must be readied for storage at the 

end of the mowing season, or if it will not be in 

use for more than thirty days.

Fuel allowed to stand for long periods of time 

(thirty days or more) can leave sticky residues 

that can plug the carburetor and disrupt engine 

function.
Fuel stabilizers are an permitted option as 

regards to the sticky residues that can occur 

during storage.

Add stabilizer to the fuel in the tank or in the 

storage container. Always use the mixing ratios 

specified by the manufacturer of the stabilizer. 

Run the engine for at least ten minutes after 

adding the stabilizer so that it reaches the 

carburetor. Do not empty the fuel tank and the 

carburetor if a stabilizer has been added.

  WARNING

!  Do not store an engine with 

fuel in the tank indoors or in poorly ventilated 

spaces where fuel vapor can come in contact 

with open flames, sparks, or a pilot light 

such as in a boiler, hot water tank, clothes 

dryer, etc. Handle the fuel with care. It is very 

flammable and can cause serious personal 

injury and property damage. Drain the fuel 

into an approved container outdoors and 

store far away from open flame or sources of 

ignition. Do not use gasoline for cleaning. Use 

a degreaser and warm water.

To ready the machine for storage:

1. 

Thoroughly clean the machine, especially 

under the mower deck. Touch up damage 

to the paint and spray a thin layer of oil on 

the underside of the mower deck to avoid 

corrosion.

2. Inspect the machine for worn or damaged 

parts and tighten nuts or screws that may 

have become loose.

3. 

Change the engine oil; dispose of properly.

4. 

Empty the fuel tanks or add a fuel stabilizer. 

Start the engine and let it run until the 

carburetor is drained of fuel or the stabilizer 

has reached the carburetor.

5. 

Remove the spark plug and pour about a 

tablespoon of engine oil into the cylinder. 

Turn over the engine so that the oil is evenly 

distributed and then refit the spark plug.

6. 

Lubricate all grease zerks, joints, and axles.

7. 

Remove the battery. Clean, charge, and store 

the battery in a cool place, but protect it from 

direct cold.

8. 

Store the machine in a clean, dry place and 

cover it for extra protection.

Service

When ordering spare parts, please specify the 

purchase year, model, type, and serial number.
Always use genuine RedMax spare parts.
An annual check-up at an authorized service 

workshop is a good way to ensure that the 

machine performs its best the following season.

31

STORAGE

Содержание 967 671101-00















































































Отзывы: