2
Drawing No. LP1107
Revised 07 2020
10.
INSTALLATION REQUIREMENTS
: Sled must be installed
inside the unit case with the hardware provided. See
“Installing the 4G LTE CAT4 Sled” for more details.
11.
WEIGHT
: 3.2 oz (90.7 g)
SIM CARD INSTALLATION & DETAILS
A SIM Card with data plan enabled has to be installed on the
DA 4G LTE CAT4 Sled before installing the sled in the DA50 or
DA70 host device. Contact your cellular provider (carrier) and
request a data account. For LTE, the carrier should provide you
with a SIM card (size: 2FF) to insert into the DA 4G LTE CAT4
Sled, along with the APN, username & password for data
connectivity as required.
Insert the SIM card(s) into the card cradle on the sled.
a. Open the cradle by sliding the
cover latch to the right.
b. Lift the edge of the cradle
upward, and insert the SIM
card into the raised hinge of
SIM card slot 1 with the
contacts facing left and the
SIM card corner notch facing
away from the sled.
c. Close the cradle cover and
slide the cover latch to the left
until it clicks to secure the SIM
card in position.
d. Verify that the SIM corner
notch lines up correctly and
the SIM is flush.
e. Repeat this step if a second
SIM is used in your application.
INSTALLING THE 4G LTE CAT4 SLED
DA50 INSTALLATION
1. Prior to installing the Sled for your DA50 application, ensure
that the unit is not receiving power.
2. Disconnect and remove your DA50 from the DIN rail.
3. Remove the DA50 unit’s front cap by squeezing the sides and
pulling.
4. Slide out the sled holder.
5. Install the sled into the sled holder and hand tighten the
captive fasteners, or use a screwdriver.
6. Re-install the sled holder containing the sled into the
Converter. Make sure it is fully seated.
7. Replace the front cap.
DA70 INSTALLATION
It is recommended that the Cellular Sled be installed into the
topmost Sled slot in the carriage of the Controller.
1. Prior to installing the Sled(s) for your DA70 Controller
application, ensure that the Controller is not receiving power.
2. Remove the carriage from the Controller case by releasing the
two retaining latches and pulling straight out from Controller.
3. Remove blank panel from the carriage slot of the target sled
installation location.
4. Install sled by aligning the two sled mounting hole fasteners,
with the controller mounting posts. Be sure locating holes on
bottom side of sled align with the locating pins on the
carriage, and the sled sits flush against the carriage.
5. Hand tighten the sled captive fasteners, or use a screwdriver
if necessary.
6. Repeat the above steps for any additional sleds.
7. Carefully align the carriage with Controller base and press
carriage into the controller.
8. Close the retaining latches to ensure the carriage is fully
seated into the Controller case.
CONFIGURING THE DA 4G LTE CAT4 SLED
DA50N CONFIGURATION
When using the Cellular Sled in your installation verify cellular
connectivity through the GUI Summary page after logging into
the DA50N Controller:
– Activation Status: “Unknown” / “Not Reg” / “Searching” /
“
Reg Home
” / “Reg Roaming” / “Reg Denied”
– Connection: “
CONNECTED
” / “Unknown
– IP Address: Populated with a network IP address (if
“CONNECTED”).
A “CONNECTED” status indicates successful connection to the
cellular network.
If connection is “Unknown”, browse to Network → Cellular
Connection → Sled Cellular Configuration, select the Sled Slot for
the DA 4G LTE CAT4 SLED, update the APN field with the
information provided by your SIM provider, click Apply, then
return to the GUI Summary page to monitor connectivity status.
For further configuration and troubleshooting information,
please refer to the DA50N Software Manual for troubleshooting
steps at
www.redlion.net/support/documentation
.
DA50D or DA70D CONFIGURATION
The CAT4 Model Sled (Cell Modem Sled) is configured using
Crimson 3.1 (or later) software. After selecting the Cell Modem
Sled, it is set up as a PPP and Modem Client or SMS via GSM
Modem. Find additional information in the Crimson 3.1 User
Manual.
ANTENNA INSTALLATION
Antennas intended for use in Class 1, Division 2 and Zone 2
Hazardous Locations must be installed within the end use
enclosure. For remote mounting in an unclassified location,
routing and installation of the antennas shall be in accordance
with the National Electrical Codes requirements.
CAUTION
: Follow standard ESD precautionary
procedures.
ATTENTION
: Suivez les procédures de précaution
standard de décharge électrostatique.
WARNING - Disconnect all power to the unit before
installing or removing sleds.
AVERTISSEMENT - Débranchez l’alimentation électrique
de l’appareil avant d’installer ou de retirer les tiroirs.
CAUTION
: Failure to properly align the carriage can
result in damage to the Sled connector pins.
ATTENTION:
Si le chariot n’est pas correctement
aligné, les broches du connecteur du chariot
risquent d’être endommagées.
