Redline Communications RedMAX AN100U Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 178

background image

B-1

Redline Communications Inc. Confidential and Proprietary

B

AN100U/UX Event Log
Messages

The following events are displayed in the sector controller event log. This list provides a
description of the message and some basic information regarding the probable cause and
possible corrective action, as applicable.

Additional information on specific messages and how the event messages are determined
are provided at the end of the table and reference from the corresponding event log
message within the table.

This following messages are grouped by functionality. Within each group, the messages
are sorted alphabetically.

•

Classification Messages

•

RF-Related Messages

•

Developer Messages

•

Startup Messages

•

IDU-Related Messages

•

Sub-Channelization Messages

•

Initial Ranging Messages

•

Synchronization Messages (See also
Appendix D, “Synchronization Event
Log Messages”.

•

ODU-Related Messages

•

Upgrade Messages

•

Restore Messages

Table B-1

AN100U/UX Event Log Messages

Message

Description

Comment

Classification Messages

NOTICE: Default Uplink
Service Flows are Disabled

No traffic will be received from the
subscriber unit while the uplink flows
are disabled.

Enable the flows as required.

NOTICE: Pass-All Classifier
has been created for SFID [x]

All unclassified traffic will be
forwarded to this downlink service
flow.

This is security issue and should not be allowed.

«
...
125
126
127
128
129
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

JEM31WF - Spacemaker II Microwave Oven

Бренд: GE Страницы: 4

and Vantage Pro

Бренд: DAVIS Страницы: 4

and Vantage Pro

Бренд: Davis Instruments Страницы: 4

Бренд: Datavideo Страницы: 45

Бренд: RaceChip Страницы: 12

Бренд: Ecco Страницы: 9

Бренд: Ecco Страницы: 9

Oakville Series

Бренд: Napoleon Страницы: 72

Бренд: Napoleon Страницы: 4

Allure Vertical Series

Бренд: Napoleon Страницы: 120

Бренд: Xerox Страницы: 16

Бренд: Yamaha Страницы: 33

Бренд: Yamaha Страницы: 17

Бренд: Sirius Satellite Radio Страницы: 8

Бренд: Datasensor Страницы: 2

Бренд: Balt Страницы: 8

Бренд: Spector&Co Страницы: 9

Бренд: Sacred Sun Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды