manualshive.com logo in svg

Redline Communications RedCONNEX AN-80i, Руководство по установке

Поделиться
Скачать
Redline Communications RedCONNEX AN-80i Скачать руководство пользователя страница 54

AN-80i 

Installation Guidelines 

70-00073-01-08-b 

Proprietary Redline Communications © 2011

 

Page 

54

 of 58 

May 27, 2011 

When the alignment is complete, tighten each bolt in a cross-pattern to minimize shifts in 
the antenna alignment. Tighten all bolts to the recommended torque. 

Note:  A  metal  tower  will  affect  the  accuracy  of  a  magnetic  compass.  Magnetic 
declination (the difference between true North and Magnetic North) must also be taken 
onto account. 

3.6.7

 

Installation Procedure for DFS-Enabled Systems 

 

 

 

Important: DFS Settings 

Where DFS is required by regional regulations, this function is permanently enabled at 
the factory and can not be disabled by the installer or end-user.

 

 

When  installing the  AN-80i  system  in  regions  that  require  DFS  to  be  enabled,  antenna 
alignment  may  be  interrupted  by  false  DFS  triggering.  DFS  events  can  disable  AN-80i 
transmissions for up to 30 minutes (Tx Off) or disable transmissions for one minute and 
change the RF frequency (Chg Freq). While the DFS feature cannot be disabled at any 
time during system operation, the following procedure is recommended to minimize the 
effects of the false triggering while aligning antennas for a single PTP link. 

Summary 

In  step  1,  the  PTP  Master  provides  an  RF  reference  while  antenna  adjustments  are 
made  to  the  PTP  Slave  operating  with  the  radio  disabled.  Operating  the  PTP  Slave  in 
listen-only  mode  while  adjusting  the  antenna  avoids  false  DFS  triggering  due  to  rapid 
changes  in  RF  signal  strength  seen  at  the  Master  unit.  In  step  2,  the  Master/Slave 
configuration is reversed to allow alignment of the remote end system antenna.  

Step A -- Align Site A Antenna 

a) Go to the location where the AN-80i is operating as a PTP Slave -- this is the Site A. 

b) Login to the remote PTP Master (Site B) and adjust the parameters to match the Site 
B  settings  in  Table  15:  Configuration  -  Settings  for  Antenna  Alignment  (DFS)  -  Step  1 
and save changes. 

c) Login to the local PTP Slave and adjust the parameters to match the Site A settings in 
Table 15: Configuration - Settings for Antenna Alignment (DFS) - Step 1 and save these 
changes. The wireless link will be lost, but the AN-80i will monitor the RF signals. 

 

Table 15: Configuration - Settings for Antenna Alignment (DFS) - Step 1  

Setting 

Site A 

Site B 

System Mode 

PTP Slave 

PTP Master 

DFS Action 

Chg Freq 

Chg Freq 

Auto Scan 

 (Enabled) 

N/A 

Radio Enable 

(Disabled) 

 (Enabled) 

ATPC 

 (Disabled) 

 (Disabled) 

 

 

Содержание RedCONNEX AN-80i



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды