red roo HT912, Инструкция по эксплуатации, безопасности и обслуживанию, Страница: 10 / 32

10
The clutch valve control should be adjusted
to completely activate the chain valve when
the dig chain control is in ‘ON’ position. To
check this adjustment, put the chain on/off
control in ON position. Pull the clutch lever
on left handle bar up until it touches the
handgrip. While holding clutch lever up, push
on the chain forward/neutral/reverse lever.
It should be at the end of its stroke, thus not
move down anymore. If the chain F/N/R lever
can be pushed down more, the valve spool
lever should be adjusted. To adjust, remove
back cover from the control panel. Loosen
the 2 bolts on the valve lever and rotate the
lever plate down about 1/16”. Re-tighten the
bolts and check the lever stroke. Adjust so
the valve lever comes to the end of its stroke
just as the clutch lever touches the handgrip
when chain valve control is in ON position.
CHAIN VALVE ADJUSTMENT
Be sure to grease all lubrication points as
outlined in this manual.
LUBRICATION
REQUIREMENTS
10
The clutch valve control should be adjusted
to completely activate the chain valve when
the dig chain control is in ‘ON’ position. To
check this adjustment, put the chain on/off
control in ON position. Pull the clutch lever
on left handle bar up until it touches the
handgrip. While holding clutch lever up, push
on the chain forward/neutral/reverse lever.
It should be at the end of its stroke, thus not
move down anymore. If the chain F/N/R lever
can be pushed down more, the valve spool
lever should be adjusted. To adjust, remove
back cover from the control panel. Loosen
the 2 bolts on the valve lever and rotate the
lever plate down about 1/16”. Re-tighten the
bolts and check the lever stroke. Adjust so
the valve lever comes to the end of its stroke
just as the clutch lever touches the handgrip
when chain valve control is in ON position.
CHAIN VALVE ADJUSTMENT
Be sure to grease all lubrication points as
outlined in this manual.
LUBRICATION
REQUIREMENTS
10
The clutch valve control should be adjusted
to completely activate the chain valve when
the dig chain control is in ‘ON’ position. To
check this adjustment, put the chain on/off
control in ON position. Pull the clutch lever
on left handle bar up until it touches the
handgrip. While holding clutch lever up, push
on the chain forward/neutral/reverse lever.
It should be at the end of its stroke, thus not
move down anymore. If the chain F/N/R lever
can be pushed down more, the valve spool
lever should be adjusted. To adjust, remove
back cover from the control panel. Loosen
the 2 bolts on the valve lever and rotate the
lever plate down about 1/16”. Re-tighten the
bolts and check the lever stroke. Adjust so
the valve lever comes to the end of its stroke
just as the clutch lever touches the handgrip
when chain valve control is in ON position.
CHAIN VALVE ADJUSTMENT
Be sure to grease all lubrication points as
outlined in this manual.
LUBRICATION
REQUIREMENTS
10
The clutch valve control should be adjusted
to completely activate the chain valve when
the dig chain control is in ‘ON’ position. To
check this adjustment, put the chain on/off
control in ON position. Pull the clutch lever
on left handle bar up until it touches the
handgrip. While holding clutch lever up, push
on the chain forward/neutral/reverse lever.
It should be at the end of its stroke, thus not
move down anymore. If the chain F/N/R lever
can be pushed down more, the valve spool
lever should be adjusted. To adjust, remove
back cover from the control panel. Loosen
the 2 bolts on the valve lever and rotate the
lever plate down about 1/16”. Re-tighten the
bolts and check the lever stroke. Adjust so
the valve lever comes to the end of its stroke
just as the clutch lever touches the handgrip
when chain valve control is in ON position.
CHAIN VALVE ADJUSTMENT
Be sure to grease all lubrication points as
outlined in this manual.
LUBRICATION
REQUIREMENTS
DAILY