Red Pawz CMR280 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 30

Red Pawz CMR280 Скачать руководство пользователя страница 12

First, please ensure that your ESC support SimonK firmware. Second, pls meet following

requirements.

A). Hex or Bin file. The firmware for the ESCs is available in a .hex or .bin file. One file

contains the complete firmware for one ESC.

B). Interface Software (eg. AVR Studio) Depending on your platform you will need dedicated

interface software installed on your computer to flash your ESC with the new firmware.

C). MCU programmer (eg. JTAG or USB ASP)

D). PIN -header or micro- clips to connect programmer to MCU Then you can flash the ESC with

the video and other information on internet.

Note: You can flash your ESC multiple times but only the last flashed firmware is active on the

micro controller. If the wrong firmware is flashed, you may end up with a damaged ESC when it's

powered by the battery supply. It's important to safely test your ESC after the firmware upgrade.

5. How to get Pre-flashed ESCs with SimonK firmware?

Flashing your own ESCs is not so easy as you download music to your iPhones. It takes time, a

flash tool and some research. For modelers who do not have any knowledge about MCU, the

flashing process is difficult. Or some model flyers just need their models fly well and do not care

about flashes. If you are in one of them, you can choose Red Pawz already flashed ESC.

6. Install your ESCs

We believe it is easy for you to install ESCs to multi-rotor platform. We still kindly remind you to

make sure the correct and solid connection of each connector to silicon wire, battery wire to power

distribution board, power distribution board to ESC, ESC to motor.

7. SimonK firmware ESC start-up tones

All ESCs make the motors sing, so does SimonK firmware ESC. When connected to power,you

need firstly unlock the flight controller. Then ESCs make 3 beeps (di da di), to tell you self

-detection finished. If flight controller also makes control instructions, a long beep (di----) will tell

you ESCs have received throttle signal from flight controller and ready to start. Then pull up the

throttle stick, motor starts to run. OK! Let's go!

«
...
10
11
12
13
14
...
»

Содержание CMR280































Отзывы:

Нет отзывов