background image

10

The Security Code determines the programming mode and the accessibility

of programming parameters. This code can be used along with the Program
Mode Lock-out (

Pro Loc

) in the User Input Function parameter (Module 1).

Two programming modes are available. Full Programming mode allows all

parameters to be viewed and modified. Quick Programming mode permits only
the setpoint output time-out and counter load values (when applicable) to be
modified, but allows direct access to these values without having to enter Full
Programming mode.

Programming a Security Code other than 0, requires this code to be entered

at the 

Pro CodE

prompt in order to access Full Programming mode. Depending

on the code value, Quick Programming may be accessible before the 

Pro CodE

prompt appears (see chart).

PROGRAMMING SECURITY CODE

The 

yES

selection will return the meter to the factory default settings. The

meter will display 

rESEt

and then return to 

Pro

, at which time all settings have

been changed.

LOAD FACTORY DEFAULT SETTINGS

to

999

yES

NO

"

#

000

Pro CodE

"

#

MO

FACt SEt

* Entering Code 222 allows access regardless of security code.

The 

yES

selection allows the 

SEL

button to toggle through the enabled

displays.

FRONT PANEL DISPLAY SELECT ENABLE (SEL)

The 

yES

selection allows the 

RST

button to reset the selected counter(s). The

shaded selections are only active when Counter B is enabled (Dual Count mode
or batch counter).

FRONT PANEL COUNTER RESET ENABLE (RST)

The 

yES

selection allows the display to automatically scroll through the

enabled displays. Each display is shown for 4 seconds.

DISPLAY SCROLL ENABLE

NO

yES

Count b

both A-b

dSPLAy

yES 

NO

NO

Count A

NO

yES

"

#

yES

SEL Enb

"

#

YES

RSt Enb

"

#

NO

d-ScroLL

Enter the desired display color, red or green. This parameter is active for

backlight units only.

DISPLAY COLOR (BACKLIGHT UNIT ONLY)

6rn

rEd

"

#

rEd

d-COLOr

Enter the desired Display Intensity Level (1-5). The display will actively dim

or brighten as levels are changed. This parameter is active for backlight units only.

DISPLAY INTENSITY LEVEL (BACKLIGHT UNIT ONLY)

"

#

5

d-LEVEL

to

5

Select 

YES

to momentarily display the meter software version before advancing

to the next parameter. The software version is also displayed at power-up. 

SOFTWARE VERSION DISPLAY

"

#

NO

CodE UEr

6.3  MODULE 3 - D

ISPLAY AND

F

RONT

P

ANEL

K

EY

P

ARAMETERS

(

3-dSPLAY

)

PARAMETER MENU

NO

yES

Immediate Access

Full Programming

0-999

Not Active

With correct code entry

at 

Pro CodE

prompt *

Pro CodE

prompt

100-999

Pro Loc

No Access

Quick

Programming

1-99

Active

No Access

Programming

Lock

0

With correct code entry

at 

Pro CodE

prompt *

Pro CodE

prompt

100-999

After Quick Programming

with correct code entry 

at 

Pro CodE

prompt *

Quick

Programming

1-99

______

not 

Pro Loc

Immediate Access

Full Programming

0

FULL PROGRAMMING

MODE ACCESS

MODE WHEN “SEL”

KEY IS PRESSED

SECURITY

CODE

USER INPUT

STATE

USER INPUT

FUNCTION

Содержание CUB5B

















Отзывы: