manualshive.com logo in svg

Red-D-Arc EX350ie, Руководство оператора

Поделиться
Скачать
Red-D-Arc EX350ie Скачать руководство пользователя страница 12

A-3

INSTALLATION   

A-3

EX350ie (CE) (RED-D-ARC) 

LN-15 Connection Instructions 

•  Turn the EX350ie (CE) power switch "off".
•  Connect  the  electrode  cable  to  the  output  terminal  of

polarity required by electrode. (See Figures below)

•   Set the meter polarity switch on the front of the EX350ie

(CE) to coincide with wire feeder polarity used.

LN-25 Connection Instructions

•  Turn the EX350ie (CE) power switch "off".
•  Connect  the  electrode  cable  to  the  output  terminal  of

polarity required by electrode.  Connect the work lead to
the other terminal.

•  LN-25 with Remote Control options can be used with the

EX350ie (CE).  The 6-Pin (K444-1) and 14-pin (K444-2)
remotes can be connected directly to the  6-pin & 14-pin
MS-style  connector.  The  42  Volt  Remote  Voltage  and
Output  Control  (K624-2)  Kit  can  be  connected  to  the
EX350ie (CE) 14-pin MS-style connector using Remote
Control Cable assembly K627- [ ].  LN-25s with a K431-1
remote kit can be connected to the EX350ie (CE) 14-pin
MS-style  connector  using  a  K432  cable  and  K876
adapter. (See connection diagram S19899).  Or the K432
cable  could  be  modified  with  a  K867  Universal  Adapter
Plug  (See  connection  diagram  S19405)  to  connect  it  to
the EX350ie (CE) 14-pin MS-style connector. 

LN-742 Connection Instructions

• Turn the EX350ie (CE) power switch "off"
•  Either  a  K591  or  a  K593  Input  cable  assembly  is

required  to  connect  the  LN-742  to  the  EX350ie
(CE). 

•  Connect  the  control  cable  from  the  LN-742  to  the

14-pin MS-style connector.

•  Connect the electrode cable to the output terminal

of  the  polarity  required  by  electrode.  Connect  the
work lead to the other terminal.

•  Set  the  meter  polarity  switch  on  the  front  of  the

Invertec to coincide with wire feeder polarity used.
The  wire  feeder  will  now  display  the  welding  volt-
age.

• If a remote control  such as K857 is to be used with

the  LN-742,  the  remote  can  be  connected  directly
to  the  6-pin  MS-style  connector on  the  front  of  the
EX350ie (CE) or use a K864 adapter to connect the
LN-742  and  the  remote  to  the  14-pin  MS-style  con-
nector.

Cobramatic Connection Instructions

•  Turn the EX350ie (CE) power switch "off"
•  Connect the control cable from the Cobramatic to

the 14-pin MS-style connector.

•  Connect the electrode cable to the output terminal

of the polarity required by electrode. Connect the
work lead to the other terminal.

•  Set  the  meter  polarity  switch  on  the  front  of  the

Invertec to coincide with wire feeder polarity used.  

•  If  a  remote  control    such  as  K857  is  to  be  used

with the Cobramatic, the remote can be connected
directly  to  the  6-pin  MS-style  connector on  the  front
of  the  Invertec  or  use  a  K864  adapter  to  connect
the  cobramatic  and  the  remote  to  the  14-pin  MS-
style connector. 

CONNECTION OF WIRE FEEDERS TO EX350ie (CE)

Wire feeders other than these listed may be used pro-
vided  that  the  auxiliary  power  supply  capacity  of  the
EX350ie  (CE)  is  not  exceeded.  K867  Universal
Adapter  Plug  may  be  required.  See  connection  dia-
gram S24985 on page F-4.

REMOTE CONTROL OF INVERTEC

Remote Control K857, hand Amptrol K963 and Foot
Amptrol K870.

uNDERCARRIAGE MOuNTINGS

14.79

12.44

3.44

21.60

27.82

5.50

10.00

MOUNTING HOLE LOCATIONS

M19527

13.10

1/4-20 NUT (4 PLACES)

NOTE:  MOUNTING SCREWS CA

4/01

N NOT PROTRUDE MORE THAN 

0.5 INCHES INSIDE THE MACHINE.

11.84

3.50

Work

Clamp

Electrode Cable

Electrode Cable

Electrode Cable

Work

Clamp

Work

Clamp

wire feeder

K1870-1

wire feeder

K1870-1

RANGER 8

SAE 400 WITH CV ADAPTER

ENGINE DRIVEN WELDERS

WITH WIRE FEED MODULE

(LOCAL MODE AND CV ADAPTER)

CV250

CV300

CV400

CC POWER SOURCE

Output Terminals

Always Hot.

Output Terminals

Always Hot.

Output Terminals

Always Hot.

Order K484 Jumper

Plug Kit.

Electrode Cable

Work

Clamp

semiautomatic

semiautomatic

semiautomatic

semiautomatic

wire feeder

K1870-1

wire feeder

K1870-1

wire feeder

K1870-1

CV655, DC400, DC600,

DC655, V350-PRO,

RANGER 9, RANGER 300 DLX

COMMANDER 300

COMMANDER 500

RANGER 2V35050

RANGER 305G

Output Terminals

Output Terminals

Always Hot.

Always Hot.

Power source contactor

Power source contactor

switch must be in the

switch must be in the

 "ON" position or use a

 "ON" position or use a

K848 Junper Plug Kit.

K848 Junper Plug Kit.

ACROSS THE ARC MODEL

EX350ie (CE)

TWIST-MATE

CONTROL CABLE MODEL

Electrode Cable

EX350ie (CE)

Содержание EX350ie

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды