RED BARON PIZZA SQUADRON'S STEARMAN Скачать руководство пользователя страница 34

Страница: 34 / 39

STEARMAN 71.5 inches

Instruction Manual.

2) Use a 2.5mm hex wrench to remove the

screws that attach the panels to the fuse-

lage and center section. Slide the panels

from the tubes and disconnect the servo

lead for the aileron servo.

Using the transport frames allow the re-

moval of the wings without the need to

remove the aileron linkage and the inter-

plane strut between the top and bottom

wings.

INSTALLATION PILOT AND

WINDSHIELD.

1) Locate items necessary to install pilot

and windshield.

2) A scale pilot is included with this ARF.

The Pilot included fits well in the cockpit.

(or you can order others scale pilot fig-

ures made by SG Models. They are avail-

able at SG Models distributors.).

If you are going to install a pilot figure,

please use a sanding bar to sand the base

of the figure so that it is flat.

3) Position the pilot figure on the cock-

pit floor as shown. Use epoxy to glue the

base of the pilot figure, please see pictures

as shown.

Содержание SQUADRON'S STEARMAN








































Результаты поиска

Содержание SQUADRON'S STEARMAN

Отзывы:

Бренды по названию

Популярные бренды

RED BARON PIZZA SQUADRON'S STEARMAN, Инструкция по сборке

Результаты поиска

Содержание SQUADRON'S STEARMAN

Отзывы:

Бренды по названию

Популярные бренды