Rebel RB-1059, Руководство пользователя

Страница: 15 / 60

tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
8. This power tool may be used by children who are above 8 years old and by persons
with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised and guided by a person who is responsible for their
safety in a cautious manner for all the safety precautions being understood and
followed.
9. Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
10. Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by
poorly maintained power tools.
11. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
12. Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed.
Use of the power tool for operations different from those intended could
result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained
Battery tool use and care
1. Do not attempt to open the battery. If the battery is damaged in any way, stop using it
and do not attempt to recharge it. Short-circuit or electric shock or explosion hazard.
2. Protect the battery pack against any heat source (e.g. direct sunlight exposure, fire,
heater etc) to prevent any damage or explosion hazard.
3. Do not expose the battery pack to water, moisture and cold. Risk of electric shock.
4. In case of damage and improper use of the battery, vapors may be released. Ensure
proper ventilation and provide for fresh air to the work area. The vapors can irritate the
respiratory system.
5. Recharge only with the charger specified by the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of fire when used with another battery pack.
6. Use power tools only with specifically designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
7. When battery pack is not in use, keep it away from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal objects, that can make a connection from
one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
8. Under abusive conditions, liquid may be ejected from the battery. Avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause irritation or burns.
9. Do not use damaged or modified batteries. Damaged or modified batteries may behave
in an unpredictable manner, resulting in hazardous effects (ignition, explosion, personal
injuries).
10. Ensure that the switch is in the OFF position before inserting the battery. Inserting the
battery into power tools with the switch on invites trouble. Injury hazard.
28 29 EN EN
11. Charge battery pack only at ambient temperatures b10°C and +40°C. Store
charger in a dry location protected from cold where temperature would not exceed
+40°C.
Charger use and care
1. Do not attempt to open or disassemble the charger. If the charger has been dropped
or is damaged in any way, stop using it and do not attempt to repair it. Return the
charger for repair to an authorized service center or a qualified person, to avoid any
danger to the user; or discard it according to local laws.
2. Protect the charger against any heat source (e.g. direct sunlight exposure, fire, heater)
to prevent any damage to the charger.
3. Do not expose the charger to water, moisture and cold. Risk of electric shock.
4. If the power cord or the plug becomes damaged, stop suing the charger until it has
been repaired by a qualified person. If the supply cord is damaged, it must be replaced
by the manufacturer or its authorized service center, in order to avoid a hazard. Risk of
electric shock.
5. Only use the charger recommended by manufacturer, or a same type or same model
charger to charge the battery. The use of other types of charger increases the risk of
electric shock, personal injury and damage.
6. Never attempt to recharge non-rechargeable batteries. Explosion hazard.
7. Only use the charger at ambient temperatures b10°C and +40°C. Store
charger in a dry location protected from cold where temperature would not exceed
+40°C.
8. The charger is intended for indoor use only. Place charger on solid, flat nonflammable
surface and away from any flammable materials when re-charging the battery pack.
9. Do not recharge the battery pack in a wet or humid environment. The charger and
battery pack may heat during charging process.
Additional safety warnings for random orbital sanders
.
• Inspect workpiece for any nails and remove them before operation. If necessary,
remove them.
• Hold the power tool with a firm grip with both hands (if possible) and keep a good
balance.
• Secure the workpiece. Never hold the workpiece in your hand or across your legs or
against your body. A workpiece clamped with clamping devices or in a vice is held more
secure than by hand. An unstable workpiece can cause loss of control of the tool and/or
injury.
• Keep hands away from the working range. Contact with the sandpaper disc lead to
injuries.
• Apply the power tool to the workpiece only when switched on. Otherwise there is
danger of kickback when the wheel jams in the workpiece.
• Do not apply too much pressure on the power tool.
• Do not use damaged sandpaper discs. Prior to each use, inspect for any cracks. If any
of these are found, replace the wheel with a new one.
• Before switching on the power tool, check if the sandpaper disc is correctly fitted, in
accordance with the cut-out holes for dust extraction.
• Do not run the power tool while carrying it at your side. Accidental contact with the
accessory could snag your clothing and damage your body.
All manuals and user guides at all-guides.com