Rear view safety RVS-770616-2133 Скачать руководство пользователя страница 6

Страница: 6 / 28

REAR VIEW SAFETY

INSTALLATION
•

Electric shock or product

malfunction may occur if

this product is installed

incorrectly.

•

Use this product within

the voltage range specified.

Failure to do so can cause

electronic shock or product

malfunction.

•

Take special care when

cleaning the monitor.

•

Make sure to firmly affix the

product before use.

•

If smoke or a burning smell

is detected, disconnect the

system immediately.

•

Where the power cable may

touch a metal case, cover the

cable with a friction tape. A

short circuit or disconnected

wire may cause a fire.

•

While installing the Rear

View System be careful with

the wire positioning in order

to avoid wire damage.

•

The Rear View System should

only be used when the vehi-

cle is in reverse.

•

Do not watch movies or

operate the monitor while

driving; as it may cause an

accident.

•

Do not install the monitor

where it may obstruct drivers

view or obstruct an air bag

device.

•

Dropping the unit may cause

possible mechanical failure.

Safety Information

Содержание RVS-770616-2133





























Результаты поиска

Содержание RVS-770616-2133

Отзывы:

Похожие инструкции для RVS-770616-2133

Бренды по названию

Популярные бренды

Rear view safety RVS-770616-2133, Руководство по установке и инструкция к продукту

Результаты поиска

Содержание RVS-770616-2133

Отзывы:

Похожие инструкции для RVS-770616-2133

Бренды по названию

Популярные бренды