background image

RTL8188CUB8 

Slim Module Combo Card User Manual

 

 

 

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop 

configurations or co-location with another transmitter), then the FCC authorization is no longer considered 

valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will 

be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC 

authorization. 

 

End Product Labeling 

This transmitter module is authorized only for use in device where the antenna may be installed such that 20 

cm may be maintained between the antenna and users. The final end product must be labeled in a visible 

area with the following: “Contains FCC ID: TX2RTL8188CUB8”. 

 

Manual Information To the End User 

The OEM integrator has to be aware not to provide information to the end user regarding how to install or 

remove this RF module in the user’s manual of the end product which integrates this module. 

The end user manual shall include all required regulatory information/warning as show in this manual. 

Industry Canada Statement 

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two 

conditions: 

1) this device may not cause interference and 

2) this device must accept any interference, including interference that may cause undesired operation of 

the device 

 

This device has been designed to operate with an antenna having a maximum gain of  3.9 dBi. 

Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required 

antenna 

impedance is 50 ohms. 

 

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that 

the EIRP is not more than required for successful communication. 

 

IMPORTANT NOTE: 

IC Radiation Exposure Statement: 

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This 

equipment should be installed and operated with minimum distance 20cm between the radiator & your 

body. 

 

 

 

 

 

 

 

 

 

 

 

 

                                                                                            

9                                                           

                            Rev.1.0

 

Содержание RTL8188CUB8















Отзывы: