Real Flame Captiva 900 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 51

background image

11 |

P a g e

Recommended Silicon – Non-acetic, neutral cure
150degc or higher temperature rated. Bostik RTV
926 or similar.
Apply an 8mm thick silicon bead fully around
heater connection approx. 10mm from the top.
Apply an 8mm thick silicon bead fully around the
lower fan connection spigot approx. 10mm from
the end.

Apply an 8mm silicon bead fully around the inside
of the flue end (heater connection end)
Fit flue clamp over flue (loosely).

Slide flue onto connection spigot fully. Tighten
clamp fully. Wipe excess silicon, visually check
connection to ensure connection is fully sealed.

Repeat above with air intake flue pipe to heater
connection.

Clip flues as required to provide adequate
support.

Connection to wall mounted fan terminal

Predrill mounting holes into wall.

Remove cover from fan terminal

«
...
10
11
12
13
14
...
»

Содержание Captiva 900




















































Отзывы:

Нет отзывов

Похожие инструкции для Captiva 900

Бренд: S&P Страницы: 36

Бренд: S&P Страницы: 16

Бренд: WARMOS Страницы: 2

Бренд: Dancover Страницы: 7

Бренд: Calienta Страницы: 58

Altherma EKHWE150A3V3

Бренд: Daikin Страницы: 10

Бренд: Maico Страницы: 16

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Cylinder Passport

Бренд: WarmFlow Страницы: 16

Бренд: UNITED Страницы: 9

Бренд: Camplux Страницы: 20

Бренд: Dimplex Страницы: 55

Radiance RADVTBB

Бренд: Vermont Castings Страницы: 52

Бренд: ORANGE Страницы: 2

Бренд: Detroit Radiant Products Страницы: 20

Бренд: S+H Nolting Страницы: 34

Бренд: Heat Outdoors Страницы: 18

Бренд: Mark Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды