IMPORTANT!
For safety reasons, the concrete wall must be capable of supporting the
combined weight of the mount and the display.
3
Display Size:
up to 30”
Maximum Load:
25 lbs.
Mounting Pattern:
75 mm x 75 mm, 100 mm x 100 mm
Tilt Range:
up to 13.8°
Pan/Swivel Range:
up to 180°
Profile:
2.9” to 13.0” (7.5 cm to 33.0 cm)
IMPORTANT!
For safety reasons, this mount must be secured to a wood stud capable of
supporting the combined weight of the mount and display. Do not mount to drywall alone.
1
Mark two locations (top and bottom) for securing the mount to the wall and set it aside (see
Fig. 2).
Drill a 1/8” pilot hole at each marked location (see Fig. 3).
Attach the wall plate to the wall using the drywall screws from the hardware kit (see Fig. 4).
Ensure that the wall plate remains level.
3
Place the wall plate against the wall over the marked stud. Make sure it is level.
2
4
5
Part 1A – Mounting to the Wall (Drywall)
SPECIFICATIONS
BOX CONTENTS
HARDWARE KIT
INSTALLATION
Read these instructions before you begin.
If you are unsure of any part of the
process, contact a professional contractor or installer for assistance. Improper
installation can result in injury or damage.
The wall or mounting surface must be capable of supporting the combined weight of
the mount and the display; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where you wish to install the mount
before drilling.
Safety gear and proper tools must be used. Failure to do so can result in injury or
damage.
Follow all instructions and recommendations regarding adequate ventilation and
suitable locations for mounting your display. Consult the owner‘s manual for your
particular display for more information.
CAUTION:
This wall mount is intended for use only with the maximum weight of 25
lbs. Use with heavier than the maximum weights indicated may result in instability
causing possible injury.
1
2
3
4
5
WARNINGS
Mount (x1)
Wall Plate (x1)
Instruction Manual (x1)
Hardware Kit (x1)
Part 1B – Mounting to the Wall (Concrete)
Mark two locations (top and bottom) for securing the mount to the wall (see Fig. 5) and set it
aside.
Drill a 5/16” hole at each marked location (see Fig. 6). Remove any excess dust from the holes.
Use a high quality stud finder to locate a stud on the wall where you wish to install your
mount (see Fig. 1). Mark both edges of the stud to help identify the exact center.
NOTE:
Use the center of the stud to avoid cracking or splitting the wood.
Fig. 4
Fig. 3
1
2
Place the wall plate against the wall in the desired location. Make sure it is level.
RSMWA10
SMALL FULL MOTION WALL MOUNT
INSTRUCTION MANUAL
INTRODUCTION
Congratulations on your purchase!
We take pride in the quality of our products and are confident you have
received one of the finest wall mounts on the market. Should you have any
questions or comments, require any assistance, or need replacement parts for
your mount, please contact us by e-mailing [email protected] or calling
1-888-530-7904. You can also visit our website for more information:
www.readysetmount.com.
IF YOU ARE NOT SATISFIED WITH YOUR MOUNT FOR ANY REASON,
PLEASE CONTACT US BEFORE RETURNING IT TO THE RETAILER.
TOOLS REQUIRED
Phillips Head Screw Driver
Electric or Portable Drill
1/8” Drill Bit and Stud Finder for Drywall Installation
5/16” Masonry Bit for Concrete Installation
Fig. 1
Fig. 2
Fig. 5
Fig. 6
1/8”
(C)
M4 x 12 Screw (x4)
(A)
Drywall Screw (x2)
(B) Concrete Anchor (x2)
(D)
M4 x 20 Screw (x4)
(F) M5x 20 Screw (x4)
(E)
M5 x 12 Screw (x4)
(H) S4 Allen Key (x1)
(G)
Spacer (x4)
