4
B
NOTE:
This mount comes with a variety of screw lengths and diameters to accommodate
different display models. Not all of the hardware in the kit will be used. If you cannot find the
appropriate screw size in the kit provided, consult with the manufacturer of your display or a
professional installer.
Part 2 – Attaching the Mount Arms to the Display
IMPORTANT!
Use extra care during this part of the installation to avoid damaging your displays.
Insert a concrete anchor (B) into each hole so that it is flush with the concrete surface (see Fig.
7). A hammer can be used to lightly tap the anchors into place if necessary.
5
Attach the upper extension pipe to the ceiling using the lag bolts and washers (A) provided
(see Fig. 8).
Do not release the mount until all bolts are secure.
If the back of your display is curved or if additional space is needed between the display
and the mount, use the longer screws.
1
A
B
A
Determine the correct length of screw to use by examining the back of your first display:
If the back of your display is flat and the mounting holes are flush with the surface, use the
shorter screws from the hardware kit.
If you are using the longer screws, you may also need to use spacers (K).
NOTE:
The mount arms must be attached with the locking tabs facing outward (i.e. away
from the middle of the display). Otherwise, the locking tabs cannot be accessed (see Fig. 14).
Attach the mount arms to the back of your display using the screws identified in steps 1 and
2
(see Fig. 9):
If you are using the M8 screws you will need to use the M8 Washers (J). If you are using
smaller screws, you will need to use the M6 washers (G).
1
Swivel adjustments can be made by simply moving your display to the desired position.
2
To change the tilt angle of your display, have one person hold the display firmly in place
while another person loosens the tilt adjustment screw located on the left side of the
mount using the S5 Allen key (P). Move your display to the desired position, then re-tighten
the screw (see Fig. 16).
Do not release the display until the tilt adjustment screw is fully
tightened.
IMPORTANT!
The M5X10 screws or padlocks must be used at all times to prevent the
displays from being accidentally knocked from the mount.
OPERATION AND ADJUSTMENT
2
Determine the correct diameter of screw to use by carefully trying one of each size from the
hardware kit.
Do not force any of the screws – if you feel resistance stop immediately
and try a smaller diameter screw.
3
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Part 3 – Final Assembly
1
4
2
3
If the ceiling is pitched or at an angle, loosen the screws at the top of the upper extension
pipe using the S6 Allen key (Q) and wrench (R) (see Fig. 10). Adjust the upper extension pipe
so that it is perpendicular with the floor, then re-tighten the screws.
Carefully route the cables from the upper extension pipe through the lower extension pipe
so they can be accessed from the bottom of the lower extension pipe.
Route any cables you wish to hide through the upper extension pipe as shown (see Fig. 11).
4
Repeat steps 1 through 3 with your second display.
Insert the lower extension pipe into the upper extension pipe as shown and move it to the
desired height. Secure the lower extension pipe to upper extension pipe using the M8 Allen
bolts (L) and M8 nuts (M) (see Fig. 12).
Both bolts must pass through both extension pipes.
5
6
Attach the cross bars to the lower extension pipe as shown in the illustration using
eight M6 cap nut (N) (see Fig. 13).
With the help of another person, carefully lift each display and place it over the
cross bars as shown in the illustration (see Fig 14).
Do not release a display until the
mount arms have securely hooked onto the cross bars.
7
Move the locking tabs located on each arm into position as shown (see Fig. 15).
Insert and tighten the four M5X10 screws (O) from the hardware kit to prevent the
displays from being accidentally lifted from the mount. Alternatively, padlocks
(not included) can be used here for theft deterrence.
3
Periodically clean your mount with a dry cloth. Inspect all screws and hardware at
regular intervals to ensure that no connections have become loose over time.
Re-tighten as needed.
RSMCM602 Rev 20170422
Fig. 7
Fig.8
Fig. 9
Fig. 10
Fig. 12
For displays with curved or
recessed backs.
For displays with
flat backs.
WARRANTY PERIOD: 1 YEAR.
Ready•Set•Mount is a registered trademark of Creative Concepts International, LLC. Supplier Warranty: Creative Concepts
International, LLC will replace this product if, due to defective parts or workmanship, it does not perform as specified by Creative Concepts International,
LLC. This limited warranty extends to the original purchaser for 1 year from the date of purchase. Creative Concepts International, LLC shall warrant any
replacement product for the remainder of the Warranty Period of the product which it replaces. In no event does this warranty extend to instances where
the product is opened or damaged through abnormal use, misuse, Installation, mishandling, neglect, accident tampering or detrimental exposure,
including without limitation: (i) abnormal wear and tear or damage caused by use or handling which is contrary to the instructions published by Creative
Concepts International, LLC, (ii) any cause beyond the control of Creative Concepts International, LLC, including without limitation conditions caused by
movement, settlement or structural defects of the environment in which the product is installed , fire, wind, hail, flood, lightning or other acts of God, any
conditions related to, or caused by, intentional acts, accidents, negligence or foreign matter or energy, or (iii) any damage to the finish of a product after it
leaves Creative Concepts International, LLC, manufacturing facility. EXCEPT FOR THE FOREGOING, THE PRODUCT IS PROVIDED AS IS AND CREATIVE
CONCEPTS INTERNATIONAL, LLC MAKES NO REPRESENTATION OR WARRANTY (WHETHER STATUTORY, EXPRESS OR IMPLIED), INCLUDING WITHOUT
LIMITATION ANY REPRESENTATION OR WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT, WITH RESPECT
TO THE PRODUCT OR OTHERWISE. TO THE EXTENT AN IMPLIED WARRANTY CANNOT BE EXCLUDED, SUCH WARRANTY IS LIMITED IN DURATION TO THE
WARRANTY PERIOD. THIS DISCLAIMER AND EXCLUSION SHALL APPLY EVEN IF THE EXPRESS WARRANTY SET FORTH ABOVE FAILS OF ITS ESSENTIAL
PURPOSE. In no event will Creative Concepts International, LLC be liable for (i) incidental, special or consequential damages arising out of the use or
inability to use the product, or (ii) any OTHER damages in excess of the purchase price arising out of the use or inability to use the product.
1
2
Fig. 11
3000000-170422
