Power
Reader may be powered by the access panel Linear Power Supply
or switch mode (provided the switching frequency is not 125kHz).
Voltage
5 to 16VDC. 12VDC at the reader is recommended for best operation.
Model
6005R
5395R
5355R
Current Draw
30-75mA
35-75mA
70-110mA
fleaPower™ Control Line
To reduce the average current required by the reader, connect the
purple conductor to ground. This will turn the LED off when inactive.
Connection
Connection must be done in accordance with NFPA 70. Do not
connect to a receptacle controlled by a switch.
Listings & Certifications
FCC compliance Statement: This device complies with part 15 of
the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Product can be used without license conditions or restrictions in
all European Union countries, including Austria, Belgium, Den-
mark, Finland, France, Germany, Greece, Ireland, Luxembourg, the
Netherlands, Portugal, Spain, Sweden, and the United Kingdom,
as well as other non-EU countries, including Iceland, Norway, and
Switzerland.
This device complies with Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interfer-
ence that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélec-
trique subi, même si le brouillage est susceptible d’en comprom-
ettre le fonctionnement.
IMPORTANT! Changes or modifications not expressly approved by
Rutherford Controls Int’l Inc. (A DORMA Group Company) could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
CAN ICES-3 (A)/NMB-3(A)
Troubleshooting
1. When the reader is first powered on it will beep 4-times and the
Red LED will be on.
2. Presenting a supported access credential will result in the reader
beeping and the LED flashing once.
NOTE: The access panel controls LED functionality, such as
switching the LED to Green.
If the reader does not recognize the card or fob (no beep, no LED
flash) or exhibits short read range, please see the table below for
possible causes and solutions.
Possible Cause
Corrective Action
Incorrect cabling
Verify gauge, connections and cabling
length
Not enough power
12VDC recommended, 5VDC at reader is
minimum
Incorrect card used Verify if card technology is supported
Reader/access
panel not properly
grounded
Earth ground needed-verify shield and
reader ground are tied at access panel and
connect to ground at one point
Supply generating
interference
Verify switching frequency of power supply
Should any of the corrective actions mentioned above not im-
prove performance, disconnect the reader from the access panel
and power it with a separate power supply or 9VDC battery and
re-test card functionality. By powering the readers separately, most
variables that may lead to reduced performance can be eliminated.
Should the problem persist, please contact RCI directly.
AWID is a trademark of Applied Wireless Identifications Group.
HID is a registered trademarks of HID Global Coporation, an ASSA
ABLOY company. Belden is a registered trademark of Belden
Technologies, Inc. All other trademarks are the property of their
respective owners. RCI reserves the right to change specifications
without notice.
© 2015 RutheRfoRd ContRols Int’l | A doRMA GRoup CoMpAny
www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: [email protected]
