RCA MRM400 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 58

background image

Copyright © 2015 RCA Communications Systems

MRM400

TM

VHF Marine Two-Way Radio Instruction Manual

4

WARNING! NEVER

cut the DC power cable

between the DC plug at the back of the

transceiver and fuse holder. If an incorrect

connection is made after cutting, the transceiver

may be damaged.

CAUTION: NEVER

place the transceiver where

normal operation of the vessel may be hindered

or where it could cause bodily injury.

KEEP

the transceiver and microphone at least 3.3

feet (1 meter) away from your vessel’s magnetic

navigation compass.

DO NOT

use or place the transceiver in areas

with tem peratures below -4°F (-20°C) or above

140°F (+60°C), or in areas subject to direct

sunlight, such as the dashboard.

DO NOT

use harsh solvents such as benzine

or alcohol to clean the transceiver, as they

will damage the transceiver’s surfaces. If the

transceiver becomes dusty or dirty, wipe it clean

with a soft, dry cloth.

BE CAREFUL!

The transceiver rear panel will

become hot when operating continuously for
long periods of time.

Place the transceiver in a secure place to avoid
inadvertent use by children.

RCA requires the radio operator to meet the FCC
Requirements for Radio Frequency Exposure. An
omnidirectional antenna with gain not greater
than 9 dBi must be mounted a minimum of 16
1/2 feet (5 meters), measured from the lowest
point of the antenna, vertically above the main
deck and all possible personnel. This is the

minimum safe separation distance estimated to

meet all RF exposure compliance requirements.
The 16 feet (5 meter) distance is based on the
FCC Safe Maximum Permissible Exposure (MPE)
distance of 10 feet (3 meters) added to the height
of an adult, 6 feet (2 meters), is appropriate for
all vessels.

«
...
2
3
4
5
6
...
»

Содержание MRM400



























































Отзывы:

Нет отзывов

Похожие инструкции для MRM400

Бренд: Galaxy Страницы: 38

Бренд: Federal Signal Corporation Страницы: 31

Бренд: Grundig Страницы: 20

Бренд: Scott Страницы: 14

Бренд: DAB Страницы: 5

SureCross DX80ER M-H Series

Бренд: Banner Страницы: 3

Бренд: La Crosse Technology Страницы: 19

Бренд: Salora Страницы: 21

Бренд: Maxon Страницы: 73

Бренд: Cobra Страницы: 38

Бренд: Fell Marine Страницы: 9

Бренд: Bosch Страницы: 30

Бренд: Bosch Страницы: 40

Бренд: Xact Страницы: 20

Бренд: Ocean Signal Страницы: 28

rescueME EPIRB1

Бренд: Ocean Signal Страницы: 34

Бренд: Quark-Elec Страницы: 15

Бренд: TFA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды