20
21
Use Default Settings
1. Press the SETUP button in stop mode.
2. Press the / button to select Misc.
3. Press the button, then press the / button to select
“Use Default Settings” dialogue box.
4. Press the ENTER button, then press the / button to
select “Yes”. Press the ENTER button and the original
setting will be restored. The unit will exit the default
setting menu automatically and re-load the disc in the disc
tray.
Note: It will take 3-5 seconds to reset the DVD player to the
factory default.
Screen Saver
1. Press the SETUP button in stop mode.
2. Press the / button to select Misc.
3. Press the button, then press the / button to select
Screen Saver.
4. Press the ENTER button, then press the / button to
change the On/Off mode.
5. Press the ENTER button.
6. Press the SETUP button or RETURN button to exit the
menu.
MISC
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a cleaning
cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause
malfunctions.
Cleaning the Unit
• Be sure to turn the unit off and disconnect the power source before maintaining the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has
been dipped in a weak soap-and-water solution and wrung out thoroughly. Then wipe with a dry cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to
remove dust.
Important Note
• Before transporting the unit, remove any disc from the disc compartment.
Maintenance
SYMPTOM
CAUSE (AND REMEDY)
• Ensure the car power adapter or AC power adapter is connected.
• Make sure that the unit is turned on.
• Remove any obstacles between the remote and the unit.
• Use the remote near the unit.
• Point the remote at the remote sensor on the unit.
• Replace the battery in the remote with new one.
• Make sure plastic sheet has been removed from battery section.
• The volume control is located on the side of the unit - please try adjusting
this.
• Make sure that you select ON mode.
• Make sure the unit is not paused. Press the PLAY button.
• Make sure the unit is not in fast-forward or fast-reverse mode. Press the
PLAY button.
• Make sure the AUDIO/VIDEO input/output connections are correct.
• The DTS DVD cannot be decoded to have speaker output.
• The unit has overheated. Shut it off for 30 minutes to allow it to cool down.
• The region number of the disc doesn't match the region number of this unit.
• The DVD is dirty. Gently clean the disc.
• The disc is scratched.
• Please adjust the LCD's brightness, contrast, color or view mode using the
VIDEO MODE button on the remote control.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with
alcohol.
• Clean the disc.
• There is no disc inside the unit ("No Disc" appears on the screen).
• Insert the disc correctly with the graphics facing up.
• Clean the disc.
• A non-NTSC disc has been inserted, or the disc region number does not match
the region number of the unit.
• Condensation may have formed inside the unit due to a sudden change in
temperature. Wait about an hour for it to clear and try again.
No power.
The remote control
does not function.
Very little or no sound
is coming from a DVD.
No picture.
The picture is not
clear.
Loud hum or noise is
heard.
The disc does not play.
Specifications and external appearance are subject to change without notice.
Troubleshooting Guide
