4
RC-TEK Ltd. SJM400 II Reference Manual
7. Upon reaching the recommended maximum height, slowly release and let off on the throttle till landing. Always maintain the helicopter’s plane level
to the ground.
8. Continually practice this technique until you can masterfully perform linear and descending paths, as well as stationary hovering capabilities.
9. As your skills improve, slowly introduce lateral movements of the helicopter; with your starting point of spot as the final goal (position). Make sure to
keep the lateral distances within 3 feet diameter. Furthering the recommended distance will increase accidental encounters.
10. once these techniques are mastered, you are now ready to elevate both your helicopter and flying skills to its potential.
11. It’s strongly recommended for softened landings, slightly tilt and allow the front part of the landing strut to touch down, followed by the rear half.
Notes:
The majority of crashes experienced by beginners are associated with behaviours of nervousness and or panic. Only a small percentage is directly related to
mechanical failures. Repetitive practice is the only way to enhance your skills such as developing controls sensitivity, awareness and understanding. Regular
maintenance is required to keep the SJM400 helicopter in optimal and safe flying condition. The model requires precise configuration of the components and
Setting to be kept by the owner. Conduct regular maintenance on the model to avoid accidents or loss and to ensure optimal performance.
Main Rotor Checklist:
1. Main Rotor housing: When the main rotor housing is worn or faulty, there will be obvious vibration and poor flight control. Check the main rotor, main shaft and feath-
ering shaft for wear or deformity. Replace parts as necessary to eliminate imbalance.
2. Main rotor holder: If the helicopter will not fly or begins to react sluggishly, even after checking for proper setting of pitch and throttle, check the
following
items:
Copyright © 2007 RC-TEK, All Rights Reserved
•
Bearings
•
Ball Bearings
•
Rotor blades
•
other relevant moving parts
4.
Check for excess play or gaps between the surfaces, missing or broken parts, binding or restricted movement, it is important to check for main
rotor balance before each flight. Operating the model when out of balance will cause wear and premature failure of parts, possibly
resulting in a dangerous situation.
Содержание SJM400 II
