GPS module
No. 20001RC
Version 03/11
iNteNded uSe
1.
This product is intended for working with the RC Logger (not included) to provide GPS information for a model vehicle.
The product is powered by the RC Logger.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
deliveRy CoNteNt
2.
GPS module
>
Logger connection cable (20 cm)
>
Module connection cable (20 cm)
>
Operating instructions
>
Safety iNStRuCtioNS
3.
Read the operating instructions carefully and especially observe the safety information. if
you do not follow the safety instructions and information on proper handling in this manual,
we assume no liability for any resulting personal injury or damage to property. Such cases
will invalidate the warranty/guarantee.
Persons / Product
The device is not a toy. Keep it out of the reach of children and pets.
>
Do not leave packaging material lying around carelessly. These may become dangerous playing material
>
for children.
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
>
flammable gases, vapours and solvents.
Do not place the product under any mechanical stress.
>
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
>
accidental use. Safe operation can no longer be guaranteed if the product:
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
-
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
>
Also observe the safety and operating instructions of any other devices which are connected to the
>
product.
Miscellaneous
Consult an expert when in doubt about operation, safety or connection of the device.
>
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
>
shop.
If you have questions which remain unanswered by these operating instructions, contact our technical
>
support service or other technical personnel.
oPeRatioN
4.
the GPS module may not work with strong electromagnetic interference. Stay away from
sources of electromagnetic interference and restart the GPS module if you have had
problems with it.
Attach the GPS module on the vehicle body firmly with cable ties, glue or double sided adhesive tape.
1.
When installing the module, you should also take care that the cables connected to the module
are not kinked nor pinched.
The side with LED should face outward and expose to the sky. The side with the sockets should
not face upward. Misplace of the module may result in a reduced ability to receive of GPS
information.
Connect the GPS module to the RC Logger with the logger connection cable provided via either socket at
2.
the bottom of the GPS module.
If you would like to install an additional module to the system, connect it to the GPS module via the other
3.
socket.
Power on the RC Logger. The red LED on the GPS module lights up for about 3 seconds indicating the
4.
module is turned on.
Then, the green LED on the GPS module lights up for about 4 seconds. This indicates the GPS module is
5.
operating and is trying to get satellite information.
The time for getting the GPS information depends on the environment. GPS module normally takes a few
6.
minutes to get the information. If the environment is good, it may take around one minute to receive the
location information. Before recording, you need to wait until the green LED blinks and two short beeps are
emitted, which indicates the location information is available.
You will hear a long beep if the location information is not available. The green LED is keep glowing and
7.
the module is trying to get the GPS signal. If the location information is ready again, the green LED blinks
and two short beeps are emitted.
Record video or takes photo with the RC Logger when the green LED on the GPS module is blinking. GPS
8.
information is recorded to the RC Logger at the same time.
Please refer to the instructions of the RC Logger for data retrieval.
9.
diSPoSal
5.
In order to preserve, protect and improve the quality of environment, protect human health and
utilise natural resources prudently and rationally, the user should return unserviceable product to
relevant facilities in accordance with statutory regulations.
The crossed-out wheeled bin indicates the product needs to be disposed separately and not as
municipal waste.
teChNiCal data
6.
Operating voltage:
3.6 – 6 V
Maximum current consumption:
100 mA
GPS sampling rate:
5 Hz
Operation temperature:
-20 to +60 ºC
Storage temperature:
-30 to +60 ºC
Internal buzzer sound pressure level:
min. 70 dB
Output data:
Date
>
Time
>
Latitude
>
Longitude
>
Altitude
>
Speed over ground
>
Course over ground
>
Number of Satellites
>
Positional Dilution of Precision (PDOP)
>
Vertical Dilution of Precision (VDOP)
>
Dimensions (W x H x D):
30 x 43 x 16 mm
Weight:
22 g
These operating instructions are published by CEI Conrad Electronic International (HK) Limited,
28th Floor & 2903-9, Pacific Plaza, 418 Des Voeux Road West, Hong Kong.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also
in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print. We reserve the right to
change the technical or physical specifications.
© 2011 by Cei Conrad electronic international (hK) limited
V1_0311-HL
