Outdoor LP Gas Griddle
Model No. GGC2241M-A
14
Before Each Use:
1 . Keep the griddle area clean and free from any
combustible materials, gasoline, and other
flammable vapors and liquids .
2 . Do NOT obstruct the flow of the combustion of LP
gas and the ventilation of air .
3 . Keep the ventilation opening(s) of the LP gas tank
area free and clear from debris .
4 . Visually check the burner flames to make sure
your griddle is working properly (Figure 11) .
5 . See sections below for proper cleaning and
seasoning instructions .
6 . Check for obstructions of airflow to the burners .
Spiders, insects and webs can clog the burner/
venturi tube . A clogged burner tube can lead to
a fire .
Cleaning Cart Surfaces
1 . Wipe surfaces clean with mild dish washing
detergent or baking soda mixed with water .
2 . For stubborn surfaces, use a citrus-based
degreaser and a nylon scrubbing brush .
3 . Rinse clean with water .
4 . Allow to air dry .
Cleaning Main Burners
W
CAUTION: Two (2) people will be
required to remove griddle.
1 . Turn LP gas tank valve to “CLOSED .”
2 . Turn all control knobs clockwise to the “ OFF”
position .
Note: A “poof” sound is normal as the last of the
gas is burned .
3 . Disconnect LP gas tank per “Disconnecting LP
Gas Tank” section .
4 . Remove griddle by lifting it off the cart .
5 . Remove burners by removing the fasteners, which
secure the burners to the frame bottom .
6 . Lift burners up and away from gas valve orifice .
7 . Disconnect wire from spark electrode .
8 . Clean venturi of each burner with small bottle
brush or compressed air .
9 . Remove all residue and dirt from burner surface .
10 . Clean any clogged ports with a stiff wire (such as
an opened paper clip) .
11 . Inspect burners for any damage (cracks or holes) .
If damage is found, replace with new burner(s)
from manufacturer .
12 . Re-install burner(s) . Checking to insure that gas
valve orifice is correctly positioned inside each
burner/venturi tube . Also, check position of spark
electrode .
13 . Connect wire to spark electrode .
14 . Replace griddle .
15 . Connect LP gas tank per “Installing LP Gas Tank” section .
16 . Perform leak test per “Checking for Leaks” section .
Before Storing
1 . Turn LP gas tank valve to “CLOSED .”
2 . Turn all control knobs clockwise to the “ OFF” position .
Note: A “poof” sound is normal as the last of the gas is burned .
3 . Disconnect LP gas tank per “Disconnecting LP Gas Tank” section .
4 . Clean all surfaces .
5 . Lightly coat the burner(s) with cooking oil to prevent excess rusting .
6 . Season your griddle per “Seasoning Griddle” section .
7 . If storing the griddle indoors, disconnect the LP tank per “Disconnecting LP Gas Tank”
section .
8 . Place the protective cap cover on the LP tank and store the tank outdoors in a well-
ventilated area out of direct sunlight .
9 . If storing the griddle indoors, cover the griddle and store in a cool dry place .
10 . If storing the griddle outdoors, cover the griddle with a griddle cover for protection from the
weather .
Seasoning Griddle
Important: season your griddle every time you use it.
Griddle chefs at Japanese steakhouses and short-order restaurants season their griddles all the
time, and it is critical for you to do it too . Seasoning helps prolong the life of your griddle, makes
the cooking surface non-stick and helps prevent rust .
5 . Turn LP gas tank valve to “OPEN .”
6 . Push and turn any control knob to (HIGH) . The
burner should light . If it does not, repeat up to
three times .
7 . If ignition does not occur in 5 seconds, turn
burner control knob “ OFF,” wait 5 minutes, and
repeat lighting procedure .
8 . If igniter does not light burner, use a lit match
secured with the Lighting Hook (included with the
griddle) to light burners . Access the burners from
under the griddle . Position lit match near side of
burner (Figures 4 and 5) .
Important:
Always use the Lighting Hook (included) when lighting burners with a match .
9 . After lighting, observe the burner flame . Make sure all burner ports are lit and flame height
matches illustration (Figure 6) .
Note
: Each burner lights independently - repeat steps 5-9 for the other burners .
W
CAUTION: If burner flame goes out during operation, immediately turn
the control knobs to the “ OFF” position, turn the LP gas tank valve
to “CLOSED” and open side shelves to let the gas clear for 5 minutes
before re-lighting.
Turning Off
1 . Turn LP gas tank valve to “CLOSED .”
2 . Turn all control knobs clockwise to the “ OFF” position (Figure 2) .
Note: A “poof” sound is normal as the last of the LP gas is burned .
3 . Disconnect LP gas tank per “Disconnecting LP Gas Tank” section .
4. Season your griddle per “Seasoning Griddle” section.
Controlling Flare-ups
W
CAUTION: Putting out grease fires by only closing the side shelves is
not possible.
1. If a grease fire develops, turn control knobs to the “ OFF” position
and LP gas tank valve to “CLOSED.” Do NOT use water on a grease
fire. This can cause the grease to splatter and could result in
serious burns, bodily harm or other damage.
2. Do NOT leave griddle unattended while preheating or burning off
food residue on
(HIGH). If griddle has not been cleaned, a grease
fire can occur.
W
WARNING: When cooking, fire extinguishing materials should be
readily accessible. In the event of an oil/grease fire, use type BC dry
chemical fire extinguisher or smother with dirt, sand or baking soda.
Do NOT attempt to extinguish with water.
Flare-ups are a part of cooking meats on a griddle and add to the unique flavor of grilling .
Excessive flare-ups can over-cook your food and be dangerous.
Important:
Excessive flare-ups result from the build-up of grease in the grease cup .
If a grease fire occurs
, turn the control knob(s) to “ OFF” until the grease burns out .
If excessive flare-ups occur,
do NOT
pour water onto the flames .
Minimize Flare-ups:
1 . Trim excess fat from meats prior to cooking .
2 . Cook high fat content meats on (LOW) setting or indirectly .
3 . Ensure that your griddle is on a hard, level, non-combustible surface and the grease is
allowed to drain into grease receptacle .
Cleaning and Care
W
CAUTION:
1. All cleaning and maintenance should be done when griddle is cool
and with the fuel supply disconnected.
2. Do NOT clean any griddle part in a self-cleaning oven. The extreme
heat will damage the finish.
3. Do NOT enlarge valve orifices or burner ports when cleaning the
valves or burners.
Notices
1. This griddle should be thoroughly cleaned and inspected on a regular basis.
2. Abrasive cleaners will damage this product.
3. Never use oven cleaner to clean any part of griddle.
Operating Instructions (continued)
Figure 7
Match
Lighting
Hook
Figure 8
OFF
HIGH
LOW
Figure 9
OFF
HIGH
LOW
Figure 10
OFF
HIGH
LOW
Figure 6
Burner
Flame
Slight
Yellow
Slight
Blue
Dark
Blue