Raytech WR14 Скачать руководство пользователя страница 76

Страница: 76 / 119

WR14 / WR50-12/13 Winding Resistance Meter Instruction Manual

Version 3.03

CABLE EXTENSIONS FOR WR100R

10M CABLE EXTENSION SET FOR THE WR100-12R

The WR100-12R is available with the optional 10m cable extension sets for the Plug type cable sets
(Note: Cable sets with the ring lug connectors do not have this option available). The Plug type
connector locking

system operates on the “push-pull” principle. It self-locks when connected. To

disconnect the Plug type connector, push in first, then pull out.

Connectors that become dirty should be cleaned with industrial alcohol before connecting.

The Cable Extension Set for the WR100-12R consists of the following cables:

10M Extensions for the Current
Cables (Positive and Negative)

10M Extensions for the Potential
Cables (Channel 1, Positive and
Negative)

10M Extensions for the Potential
Cables (Channel 2, Positive and
Negative)

It is possible to connect multiple 10M extensions together to increase the length.

Содержание WR14
























































































































Результаты поиска

Содержание WR14

Отзывы:

Похожие инструкции для WR14

Бренды по названию

Популярные бренды

Raytech WR14, Инструкция по эксплуатации

Результаты поиска

Содержание WR14

Отзывы:

Похожие инструкции для WR14

Бренды по названию

Популярные бренды