Raypak TempTracker mod+ Hybrid Скачать руководство пользователя страница 19

Страница: 19 / 56

TempTracker mod+ Hybrid Installation and Operation Manual

HTC# 059105-00D

- EMS INPUT MODE -

Disable

Enable

BACK

▲

▼

SAVE

-EMS 4ma SETPOINT -

[ ]

BACK

▲

▼

SAVE

-EMS 20ma SETPOINT-

220

[

]

BACK

▲

▼

SAVE

ModulatInG and staGInG startup Menu

note

To be able to change the

TempTracker mod+ Hybrid settings the

Program/Run Switch must be set to

Program. The switch is located under the

Enclosure Wiring Cover for security. The

Enclosure Wiring Cover can be secured

using a lock.

-------- SETTINGS ----

Season

Winter

System Target 140

BACK

▲

▼

SELECT

-- ARE YOU SURE? --

Yes

BACK

▲

▼

SAVE

PROVE/DHW SHARING

Prove

DHW Priority

DHW No Priority

No Priority (Summer)

BACK

▲

▼

SAVE

- DHW SETPOINT -

180

[

]

BACK

▲

▼

SAVE

- SETBCK/SHUTDOWN -

Shutdown/Disable

Tstat/Enable

Setback

BACK

▲

▼

SAVE

--- BOOST MODE ---

30 Minutes

Disable

BACK

▲

▼

SAVE

--- SENSOR FAULT ---

All Off

All On

BACK

▲

▼

SAVE

shutdown or

tstat

setback

--- BOILER TYPE ---

Modulation

Staging

Hybrid

BACK

▲

▼

SAVE

-- SENSOR TYPE --

Reset

Set Point

BACK

▲

▼

SAVE

set

point

enable

disable

-- BOILER NUMBER --

[ ]

BACK

▲

▼

SAVE

-- OUTPUT TYPE --

On/Off

2-Stage

3-Stage

4-Stage

BACK

▲

▼

SAVE

- STAGING MODE -

LO/HI/LO/HI

LO/LO/HI/HI

BACK

▲

▼

SAVE

staging

-- OUTPUT A TYPE --

4-20mA

0-10volt

1-10v Custom

BACK

▲

▼

SAVE

-- BOILER NUMBER --

[ ]

BACK

▲

▼

SAVE

- MODULATING MODE -

Normal

Parallel

BACK

▲

▼

SAVE

Modulation

ptions

Yes

--- BACNET MODE ---

Disable

Enable

BACK

▲

▼

SAVE

Содержание TempTracker mod+ Hybrid

























































Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды

Raypak TempTracker mod+ Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды