background image

Hydraulic Linear Drive - Installation Guide

7

Suppression ferrites

The following illustration shows typical cable suppression ferrites 
used with Raymarine equipment. Always use the ferrites supplied by 
Raymarine.

            

Figure 3: Typical Suppression Ferrites

Connections to other equipment

If your Raymarine equipment is to be connected to other equipment 
using a cable not supplied by Raymarine, a suppression ferrite MUST 
always be attached to the cable near to the Raymarine unit.

2. Mounting the drive components

Mounting the drive components involves four main steps: 

ensuring correct hydraulic ram alignment

securing the hydraulic ram to the boat

connecting the hydraulic ram to the steering system

installing the other parts of the drive system

Ram alignment

When mounting the hydraulic ram, check that it is aligned correctly: 

The ram must be at right angles to the mounting surface (see 
Figure 4). 

The ram must be at right angles to the tiller arm when the rudder is 
amidships (see Figure 4). 

The push rod must be accurately aligned with the tiller arm plane 
of rotation. The ball end fitting only allows up to 5 degrees 
misalignment between the push rod and tiller arm plane of 
rotation (see Figure 5). 

D3548-2

Содержание Hydraulic Linear Drive


















Отзывы: