background image

6.2 Power up troubleshooting

Product does not turn on or keeps turning off

Possible causes

Possible solutions

Blown fuse / tripped
breaker.

1.

Check condition of relevant fuses and breakers and connections,
replace if necessary. (Refer to the

Technical Specification

section of

your product’s installation instructions for fuse ratings.)

2. If fuse keeps blowing check for cable damage, broken connector pins

or incorrect wiring.

Poor / damaged /
insecure power supply
cable / connections

1.

Check that the power cable connector is correctly orientated and fully
inserted into the display connector and locked in position.

2. Check the power supply cable and connectors for signs of damage or

corrosion, and replace if necessary.

3.

With the display turned on, try flexing the power cable near to the
display connector to see if this causes the unit to restart or lose
power. Replace if necessary.

4.

Check the vessel’s battery voltage and the condition of the battery
terminals and power supply cables, ensuring connections are secure,
clean and free from corrosion. Replace if necessary.

5. With the product under load, using a multi-meter, check for high

voltage drop across all connectors / fuses etc, and replace if
necessary.

Incorrect power
connection

The power supply may be wired incorrectly, ensure the installation
instructions have been followed.

Product will not start up (restart loop)

Possible causes

Possible solutions

Power supply and
connection

See possible solutions from the table above, entitled ‘Product does not
turn on or keeps turning off’.

Software corruption

1.

In the unlikely event that the product’s software has become
corrupted, try downloading and installing the latest software from the
Raymarine website.

2. On display products, as a last resort, attempt to perform a ‘Power

on Reset’. Be aware that this will delete all settings / presets and
user data (such as waypoints and tracks), and revert the unit back
to factory defaults.

Performing a power on reset - Axiom Pro

Important:

Before performing a power on reset ensure you have backed up your settings and user data to
a memory card.

1. Switch off power at the breaker to ensure that the MFD is completely powered off, and not in

Standby mode. Alternatively, remove the power cable from the display.

2. Within approximately 10 seconds of powering on your MFD, press and hold the

Back

and

Switch

active

buttons until the screen goes black and the Raymarine logo appears.

The MFD will boot into Recovery mode.

3. Use the directional controls to highlight

Wipe data/factory reset

.

4. Press

Ok

.

5. Select

Yes

to restore your MFD to factory default settings.

6. When ‘Data wipe complete’ is displayed, select

Reboot system

now.

Troubleshooting

53

Содержание AXIOM PRO





















































































Отзывы: