manualshive.com logo in svg

Raymar RM16M VAC-R, Руководство пользователя

Поделиться
Скачать
Raymar RM16M VAC-R Скачать руководство пользователя страница 10

 
 

0049-1200-XXX                                                                       RM16M   –   USER’S GUIDE                                                               12/29/2010 
Rev.  C 

                                                                                                             Page 5

 

of

 

27

            

 

CHAPTER TWO – INSTALLATION

 

 
This chapter describes how to install the Data Shelf. 
 
 

UNPACKING and INSPECTING the EQUIPMENT 

Unpack the equipment and compare the contents to the packing list.  Inspect the equipment for any 
damage that may have occurred in shipment.  If you see any damage or if items are missing, contact 
Raymar-Telenetics.  Keep the shipping container and packing material for future shipment. 

 

SITE PREPARATION

 

When selecting a location to install the Data Shelf, choose a site that: 

•

 

Is clean, well lit, and free from extremes of temperature, humidity, appreciable shock, and 
vibration. 

•

 

Is within seven feet of a power source that can furnish 48 ±4 VDC at 3.5 amps, or 90 – 265 
VAC. 

•

 

Is within 50 feet of the associated data terminal. 

•

 

Provides at least 36 inches of clearance at the front for operating and maintenance accessibility. 

•

 

Provides at least 4 inches at the back of the enclosure for interface cable clearance and 
unobstructed airflow. 

•

 

Provides at least 1U above and below the enclosure for airflow. 

 

Side and top clearances for rack-mounted equipment are dictated by the rack-cabinet provisions, but 
should allow a free flow of cooling air (Figure 2-1).  An optional fan tray (1U), part number 0058-1639-
005 (see below), can be installed to improve airflow. 

                                

 

                                          

Содержание RM16M VAC-R

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды