Rayjet R400 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 83

background image

1.2 Explanation of symbols

Important technical safety notes and instructions in this manual are indicated by symbols. It is important to
observe and follow these notes and instructions on workplace safety. Avoid accidents, personal injury and
material damage to property by acting with extreme caution.

Danger

This symbol indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.

Warning

This symbol indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.

Warning Current

This symbol warns of potentially dangerous situations related to the electric voltage. Failure to
observe the safety instructions leads to risk of serious injury or death. Particular care should be
taken during maintenance and repair work.

Warning Laser

This symbol warns of potentially dangerous situations related to the laser beam. Failure to
observe the safety instructions leads to risk of serious injury.

Caution

This symbol indicates a potentially hazardous situation which, if not avoided, could result in
minor or moderate injury.

Notice

This symbol indicates potential risks of damage to the supported product (or to property).
In addition, non-observance may result in damage, malfunction or failure of the machine.

Information

This symbol indicates tips and information which must be observed for efficient and trouble-free
handling of the product.

Disposal

This symbol indicates notes regarding the professional disposal of the product or accessories.

ENGLISH (Translation)

07/2021

9 / 83

«
...
7
8
9
10
11
...
»

Содержание R400




















































































Отзывы:

Нет отзывов

Похожие инструкции для R400

Camm-1 PNC-1200

Бренд: Roland Страницы: 53

Бренд: Royal Catering Страницы: 17

Бренд: Rubi Страницы: 12

Бренд: CNC Страницы: 16

Бренд: Cub Cadet Страницы: 20

Бренд: Toro Страницы: 44

Бренд: SIZZIX Страницы: 36

Бренд: LaserMech Страницы: 68

Бренд: O-Mac Страницы: 88

Бренд: SILLA Страницы: 36

Бренд: Secabo Страницы: 21

Бренд: Martin Yale Страницы: 8

Бренд: Land Pride Страницы: 82

Бренд: FarmBoy Страницы: 28

Бренд: Varan Motors Страницы: 8

Бренд: Tanaka Страницы: 42

Бренд: Surtek Страницы: 20

Бренд: Baier Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды