Raycus RFL-C1000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 44

background image

Wuhan Raycus Fiber Laser Technologies Co., Ltd

U

ser Guide of 1000W CW laser

Raycus User Guide |

Using the Product

32

7) Set laser power (laser power is set by 0-10V analog when AD mode is

enabled, laser power is set by serial port or Ethernet when AD mode is
off)

8) Send a light enable signal to the laser in one of the following ways

●Interface gives light enabling signal (connect 24V between pin18 and
pin20)

●serial port or Ethernet interface to issue the shutter open
command-enable light

9) The On/Off of the laser is controlled by the "modulation" signal provided

by the external mod interface;

Shutdown the laser, please refer to 4.8

4.7.4 AD Mode

The laser enters the external AD mode through the upper computer selection.

The laser power is controlled by the voltage between pin12-14 of DB25 control
interface (0v-0% power, 10v-100% power).

If the upper computer selects external AD mode off, the laser power is set by

serial port or Ethernet, and the Raycus hand-heldwelding laser will enter external
ad mode by default when powered on.

«
...
33
34
35
36
37
...
»

Содержание RFL-C1000













































Отзывы:

Нет отзывов

Похожие инструкции для RFL-C1000

Бренд: Accurate Logic Страницы: 50

Acuvim-L Series

Бренд: AccuEnergy Страницы: 188

Бренд: VAMP Страницы: 78

Бренд: Hameg Страницы: 44

Бренд: Hameg Страницы: 60

Бренд: Hameg Страницы: 28

Бренд: HAMAR LASER Страницы: 113

Бренд: i-SENS Страницы: 50

BLITZFIRE Series

Бренд: Task Force Tips Страницы: 20

Бренд: Fluidwell Страницы: 48

Бренд: Magnescale Страницы: 2

Бренд: Datakom Страницы: 27

Бренд: Sonel Страницы: 26

Бренд: SellEton Scales Страницы: 30

Бренд: Jaquet Страницы: 27

Micropilot S FMR533

Бренд: E+H Страницы: 12

Бренд: National Instruments Страницы: 169

Бренд: LaserLiner Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды