Rayco RG55R, Инструкция оператора, обслуживания и технического обслуживания

Страница: 15 / 72

RG55R Operation • Service • Maintenance
800.392.2686
15
Safety
familiarize yourself with each label until you completely
understand the warning intended. Do not violate any such
warnings!
Keep all decals in place and in good condition:
• Use soap and water to keep decals clean. DO NOT
use mineral spirits, abrasive cleaners or other similar
cleaners which will damage the decals.
• Replace any damaged or missing decals. Before
attaching decals, the surface temperature of the metal
must be at least 40 degrees. The metal should also be
clean and dry before attaching the decal.
• If a machine component to which a decal is attached is
replaced, be sure to replace the decal as well.
• Replacement decals may be purchased from Rayco Mfg
or your Rayco dealer.
Visibility Information
Before you start the machine, perform a walk-around
inspection in order to ensure that there are no hazards
around the machine.
While the machine is in operation, constantly survey the area
around the machine in order to identify potential hazards as
hazards become visible around the machine.
It may not be possible to provide direct visibility on large
machines to all areas around the machine. Appropriate job
site organization is required in order to minimize hazards that
are caused by restricted visibility. Job site organization is a
collection of rules and procedures that coordinates machines
and people that work together in the same area. Examples
of job site organization include the following:
• Safety instructions
• Controlled patterns of machine movement and vehicle
movement
• Workers that direct traffic to move when it is safe
• Restricted areas
• Operator training
• Warning symbols or warning signs on machines or
on vehicles
• A system of communication
• Communication between workers and operators prior
to approaching the machine
Modifications of the machine configuration by the user that
result in a restriction of visibility shall be evaluated.
Before Starting Engine
Start the engine only from the operator station or remote if
equipped. Never short across the starter terminate or across
the batteries. Shorting could damage the electrical system
by bypassing the engine neutral start system.
Before you start the engine and before you move the machine,
make sure that no one is underneath the machine, around
the machine, or on the machine. Make sure that the area is
free of personnel.
Engine Starting
If a warning tag is attached to the start switch or to the controls,
do not start the engine. Also, do not move any controls.
Move all hydraulic controls to the NEUTRAL position before
you start the engine.
Diesel engine exhaust contains products of combustion
which can be harmful to your health. Always start the engine
in a well ventilated area. Always operate the engine in a
well ventilated area. If you are in an enclosed area, vent the
exhaust to the outside.
Operation
Only operate the machine controls when the engine is running.
Do not leave the operators station while machine is running
unless equipped with a remote.
Before you move the machine, you must be certain that no
one will be endangered.
While you operate the machine and the work tool slowly in
an open area, check for proper operation of all controls and
all protective devices.
Do not allow riders on the machine.
Note any needed repairs during machine operation. Report
any needed repairs to certified service technician.
Use only Rayco Approved Work Tools on this machine. Obey
all the lift restrictions. Refer to Operation and Maintenance
Manual, “Rayco Approved Work Tools” for the approved
work tools and the lift restriction information.
Do not go close to the edge of a cliff, an excavation, or an
overhang.
If the machine begins to sideslip downward on a grade,
immediately turn the machine downhill.
Avoid any conditions that can lead to tipping the machine.
The machine can tip when you work on hills, on banks and on
slopes. Also, the machine can tip when you cross ditches,
ridges or other unexpected obstacles.
Avoid operating the machine across the slope. When possible,
operate the machine up the slopes and down the slopes.
NOTICE
The intended use(s) of this machine e.g. Outdoor
use only, Trained Operators only.