Raycap ProSMS 8 Скачать руководство пользователя

Страница: 22 / 24

2017 ©Raycap • All rights reserved
130 620 300 Rev.C 171116

Page 22 of 24

ProSMS 8

INSTALLATION MANUAL

www.raycap.com

7.4

Min/Max measurement

Minimum/Maximum registers values

•

The Min/Max registers hold the minimum and maximum values of Current from the time the

registers were last reset.

•

The Min/Max registers can be helpful in identifying bad electrical connections.

This can be achieved by calculating difference between Min values among nearby Strings.

Where one string is shown to have greater difference, it may indicate a possible problem with

the terminal connections.

7.5

Surge counter

The ProSMS has a built in surge counter which is capable of detecting and counting direct and

indirect surges to the panels, string cables or cabling to the central inverter.

The Surge counter has been optimized to work best with the Raycap PV ProTEC

surge protection series of SPDs.

CAUTION

VOLTAGE

DANGER

WARNING

NOTICE

Содержание ProSMS 8
























Результаты поиска

Содержание ProSMS 8

Отзывы:

Похожие инструкции для ProSMS 8

Бренды по названию

Популярные бренды

Raycap ProSMS 8, Руководство по установке

Результаты поиска

Содержание ProSMS 8

Отзывы:

Похожие инструкции для ProSMS 8

Бренды по названию

Популярные бренды