manualshive.com logo in svg

Raven SBGuidance Side-Shift, Руководство по установке

Поделиться
Скачать
Raven SBGuidance Side-Shift Скачать руководство пользователя страница 28

 

Pag 28/

30

 

I SBG-Side-Shift-IM-EN-V1.1 

SBGuidance Side-Shift I Version 1.1 I CAN 

3.7. Checking centre adjustments 

The centre position of the Side-Shift system is 
important in order to ensure the correct 
successive follow-up of work operations. If the 
DynamIQ is calibrated and the GPS antenna is 
positioned physically in the centre of the 
implement, generally only a few cm need to be 
corrected.  

Follow the steps described below: 

1.  First check the centre of the tractor. 

Does the tractor drive back and forth in 
the same track?  

2.  The stabilization of the hitch must be 

locked. 

3.  Check that the correct working width has 

been entered. 

4.  Ensure that the Side-Shift system steers 

accurately with minimal or no deviations 
before the distance to the next furrow is 
measured. 

5.  Adjust the centre of the implement by 

half the measured error. The centre can 
be adjusted with the aid of the centre 
offset (Figure 29) in SBGuidance under 
Settings > Vehicle > Tuning > tab page 
Implement). 

 

 

Figure 29 Centre offset Side-Shift Steering

 

Содержание SBGuidance Side-Shift































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды