background image

Raven Industries will not assume any expense or liability for repairs 
made outside our facilities without written consent. Raven Industries 
is  not  responsible  for  damage  to  any  associated  equipment  or 
products  and  will  not  be  liable  for  loss  of  profit  or  other  special 
damages.  The  obligation  of  this  warranty  is  in  lieu  of  all  other 
warranties,  expressed  or  implied,  and  no  person  or  organization  is 

authorized to assume any liability for Raven Industries.

Damages caused by normal wear and tear, misuse, abuse, neglect, 
accident,  or  improper  installation  and  maintenance  are  not  covered 

by this warranty.

What Does this Warranty Cover?

How Long is the Coverage Period?

How Can I Get Service?

What Will Raven Industries Do?

What is not Covered by this Warranty?

Bring the defective part and proof of purchase to your Raven Dealer.

If your Dealer agrees with the warranty claim, the Dealer will send the 
part and proof of purchase to their distributor or to Raven Industries 

for final approval.

Upon confirmation of the warranty claim, Raven Industries will, at our 
discretion,  repair  or  replace  the  defective  part  and  pay  for  return 

freight.

RAVEN  INDUSTRIES

Limited Warranty

This warranty covers all defects in workmanship or materials in your 

Raven Applied Technology Product under normal use, maintenance,

and service.

Raven Applied Technology Products are covered by this warranty for 
12 months after the date of purchase. This warranty coverage applies 

only to the original owner and is nontransferable.

Содержание PowerGlide AutoBoom

















Отзывы: