Raven Apache AS1040 Скачать руководство пользователя страница 9

Страница: 9 / 28

CHAPTER

Introduction: Preparing for Installation

CHAPTER 2

INTRODUCTION

Congratulations on your purchase of the VSN system!

The following instructions are designed to assist with the proper installation of the VSN system. Refer to the VSN

Calibration & Operation Manual (P/N 016-2020-001) for assistance with calibrating and using the VSN system.

PREPARING FOR INSTALLATION

Before installing the VSN system, park the machine where the ground is level, clean, and dry. Turn off the machine

and leave it turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this

manual to complete the installation process.

PREREQUISITES

The following components must be installed with the VSN system.
• RS1™
• Viper® 4 with ROS version 3.4 or newer

Follow the installation instructions provided with these components before installing VSN.

RECOMMENDATIONS

Raven Industries recommends the following best practices when installing or operating the VSN system for the

first time or at the start of the season:
• Install the VSN unit in the recommended location.
• Use part numbers to help identify parts.
• Do not remove the plastic wrap from a part until it is necessary for installation.

POINT OF REFERENCE

The instructions in this manual assume that you are standing behind the machine, looking toward the cab.

Содержание Apache AS1040




























Результаты поиска

Содержание Apache AS1040

Отзывы:

Бренды по названию

Популярные бренды

Raven Apache AS1040, Руководство по установке

Результаты поиска

Содержание Apache AS1040

Отзывы:

Бренды по названию

Популярные бренды