Ravelli Flexi 11, Руководство по эксплуатации и обслуживанию

Страница: 34 / 64

Use and maintenance manual Flexi 11
Pag.34
Rev.1 04/03/2021
CONTROLS AND USE
Control panel description
1
2
6
3
4
5
Button 1 : Switch on/off
POWER SETTING
You can use button 2 to adjust the power. To increase the power, press button 2 again.
- Only LED 3 lit = power 1
- LED 3 lit and LED 4 flashing = power 2
- LED 3 and 4 both flashing = power 3
- LED
3
flashing and LED
4
lit = power 4
- LED 3 and 4 both lit = power 5
LED 6 (red): Error
7
: Handheld cable connection socket
In order to operate correctly, the handheld set should be interfaced with the electronic board installed inside the stove. For this
reason, on display appears the following message:
The yellow flashing LEDs (
3 , 4
) indicate that the circuit board is waiting to receive the signal from the handheld set.
Handheld touch radio initialization
The handheld, after a first short screen showing the Ravelli logo, will list the languages available in the menu.
Select the desired language with the scroll buttons and confirm your selection with the confirmation button.
User’s manual HANDHELD TOUCH RADIO User’s manual HANDHELD TOUCH RADIO
Pag.20 Pag.21
Vers. 01 of:07.04.14 Vers. 01 of:07.04.14
2
3
1
2
3
1
FIRST INSTALLATION?
PRESS THE KEY RADIO
ADJ ON THE STOVE
YES
MENU USER USER
SETTINGS
SETTINGS
DATE-TIME
USER
COMFORT CLIMA
MANUFACTURER
ENGINEER
ENABLE EXT. TH.
CONTRAST
FW VERSION
ADJUST
LANGUAGE
SCREW FEEDING
CHRONOTHERMOSTAT
AIR-PELLET SET
STOVE STATE
Handheld touch radio initialization
In order to operate correctly, the handheld set should be interfaced with the electronic board installed inside the stove. For this
reason, on display appears the following message:
If the handheld set is used for the first time, select YES using the selection keys and confirm with the dedicated key.
On the display of the handheld set appears the following:
Hold down for a few seconds the button of radio communication (RADIO ADJ) of the PCB, located on the back of the stove, to
initialize the device.
The flashing yellow LED indicates that the circuit board is waiting to receive the signal from the handheld set.
By pressing the enter key on the handheld set, the components start communicating with each other. A check sign on the display,
accompanied by a sound signal, shows that the initialization of the handheld set has been completed sucessfully .
When you replace the batteries, you do not have to run the initialization procedure of the handheld set. In this case, when
on display appears the message “FIRST INSTALLATION ?”, select
NO
and press the confirmation key.
Description of the display
The display of the handheld set is described below (in stand-by mode):
After 5 minutes of inactivity, the display of the handheld set turns dark, switching to “SLEEP” mode, while maintaining the
radio connection with the stove. By pressing the key ON/OFF, the display becomes active again.
The first pressure of any key with the display active, lights up its backlight, but it is not, however ,
considered a command.
The display is subdivided into three parts:
1. It shows the current room temperature measured by the handheld set. Moreover, if you press the DOWN scroll key you will
display the temperature settings that can be changed using the two UP/DOWN keys. Any change made is confirmed automatically
within 3 seconds from the change or by pressing the confirmation key. A sound signal indicates that the change has been con -
firmed.
In the inactive phases (combined with the 3rd part of the display) indicates the state of the stove.
In the active phases, it indicates the operating power of the stove.
In addition, by pressing the DOWN scroll button, you can display the power settings, that can be edited using the two scroll
keys
UP/DOWN: The confirmation of any change takes place automatically within 3 seconds from the change or by pressing the con -
firmation key. A sound signal indicates that the change has been confirmed.
Time and date setting
Below are given the steps for accessing the relative menu.
Press the key “access menu” to
access
the
MENU page
Press the key
“confirm” to
access the
SETTINGS
page
Press the key
“confirm”
to access the
USER page
Press the key “con -
firm”
to access the page
DATE-TIME
Press the key “selection” for
“selection”
to switch to the second page
of USER MENU and select
SETTINGS.
Press the increase key to change every single value
Press the increase key to change every single value
Press “confirm” to confirm the settings and switch to the next
value.
By pressing the key “back” for several times you will display
the stand-by page.
PRESS THE TWO
KEYS ON THE
EMERGENCY
If the handheld set is used for the first time, select YES using the selection keys and confirm with the dedicated key. On the display
of the handheld set appears the following:
Press and hold the emergency console buttons ( 1 , 2 ) for a few seconds to initialize the handheld.
By pressing the dial key on the handheld, the components communicate with each other. A check mark on the display, accompanied
by an acoustic signal, indicates that the handheld initialization operation has been successfully completed.
📌
In case of battery replacement, it is not necessary to perform the initialization procedure of the handheld computer. In this
case, when the display will show the message “FIRST INSTALLATION ?”, select NO and press the dial key.
7