background image

5

10

66

MANUAL

As defined in the „Law of Liability for Products” (§4 Prod-HaftG), for the liability of the manufacturer, for his products, the above 
information has to be regarded. The disregard of this manual, releases the manufacturer from his liability. 

This manual is part of the delivered product and describes the safe and proper use.

Safety Information: 

 

The product complies with the prior art and the recognized safety rules at the time of delivery.

 

- Pay attention to child safety.

 

- No additional load to the doors.

 

- Structural changes, additions or modifications can only be carried out by a dealer.

 

- In case of malfunctions or irregularities: shut down the system and contact your dealer.

 

-     For Installation without wall connection: use of stopper is obligatory!

Designated use: 

The product is designed and manufactured for indoor use.

 

 

The product was designed as a hand-guided sliding door that 
is usually not being moved faster than walking speed and 
should be stopped manually when reaching the end position.

 

The doors are guided on top track.

 

 

Any other use that deviates from the specific proper use is not 
according to the 

raumplus

 regulations.

 

 

Manual: 

Open the door by the handle profile or the handle (optional).

 

 

Guide the door slowly to the …

 

… opening / closing point.

 

 

Attention: 

Preserve your hands from getting trapped during the mo

-

vement of the door. When closing or opening the door never 
grasp the profile,only use the handle profile or the handle.

 

 

Use the door as instructed.

Содержание 800 AIR-B Series






























Отзывы: