manualshive.com logo in svg

Rato RG3.6-100Q-Z-II, Руководство пользователя

Поделиться
Скачать
Rato RG3.6-100Q-Z-II Скачать руководство пользователя страница 37

 

37 

 

flash-point solvent and all detergents allow to be dried thoroughly. Dip the 

element in clean engine oil and squeeze out all the excess. The engine will 

smoke during initial start –up if too much oil is left in the foam. 

Paper element: Tap the element lightly several times on a hard surface to 

remove excess dirt or blow compressed air through the filter from the inside 

out. Never try to brush the dirt off, for so doing will force dirt into the fibers. 

PAPER ELEMENT 

FOAM ELEMENT 

 

 

 

 

 

6. Fuel Strainer Cup Cleaning 

WARNING :Gasoline is highly flammable and explosive under certain 

conditions. Do not smoke or allow flames of sparks in the area. 

Turn the fuel valve to the OFF position and remove the fuel strainer cup 

and the O-ring. Wash the removed parts in solvent, dry them thoroughly and 

reinstall them securely. Turn the fuel valve ON and check for leaks. 

(1) O-RING 

(2) FUEL STRAINER CUP           

 

 

 

 

Содержание RG3.6-100Q-Z-II

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды